Home › Power Source / Network › 3ZR-FAE BATTERY / CHARGING › GENERATOR › from 2015.04
RM3090E _57 Power Source / Network _008394 3ZR-FAE BATTERY / CHARGING _0046853 GENERATOR G

3ZR-FAE BATTERY / CHARGING  GENERATOR  INSPECTION  


PROCEDURE

Hide 27415 1.INSPECT GENERATOR PULLEY WITH CLUTCH

a.
A315871C01
0.823,0.458 1.135,0.615 0.313,0.156 10 false *a 2.656,0.469 2.969,0.625 0.313,0.156 10 false *b
*a Free
*b Lock


Hold the center of the generator pulley with clutch, and confirm that the outer ring turns counterclockwise and does not turn clockwise.

If the result is not as specified, replace the generator pulley with clutch.


Hide 27370 2.INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

a.
A284139C02
0.625,0.802 0.938,0.958 0.313,0.156 10 false *a
*a Brush Length


Using a vernier caliper, measure the brush length.

Standard exposed length:

9.5 to 11.5 mm (0.374 to 0.453 in.)


Minimum exposed length:

4.5 mm (0.177 in.)


If the brush length is less than the minimum, replace the generator brush holder assembly.


Hide 27330 3.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A298011

Check that the generator rotor bearing of the generator rotor assembly is not rough or worn and that it rotates smoothly.

If necessary, replace the generator rotor assembly.


b.

Check the generator rotor assembly for an open circuit.

i.
A153720C14
1.771,1.052 2.313,0.594 2.313,0.594 1.927,1.104 true 2.333,0.458 2.646,0.615 0.313,0.156 10 false *a
*a Slip Ring


Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 100 A Type):
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.8 to 2.2 Ω


Standard Resistance (for 130 A Type):
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.55 to 1.95 Ω


If the result is not as specified, replace the generator rotor assembly.



c.

Check the generator rotor assembly for a short to ground.

i.
A153814C09
2,1.375 2.5,0.771 2.5,0.771 2.771,0.771 false 1.563,0.615 1.885,0.313 1.885,0.313 2.177,0.313 false 2.813,0.688 3.125,0.844 0.313,0.156 10 false *a 2.219,0.25 2.531,0.406 0.313,0.156 10 false *b
*a Slip Ring
*b Rotor Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Slip ring - Rotor core Always 10 MΩ or higher


If the result is not as specified, replace the generator rotor assembly.



d.

Check each slip ring.

i.

Check that the slip rings are not rough or scored.

If the slip rings are rough or scored, replace the generator rotor assembly.


ii.
A182587C04
0.552,0.596 0.712,0.748 0.16,0.152 10 *a
*a Diameter


Using a vernier caliper, measure the slip ring diameter.

Standard diameter:

14.2 to 14.8 mm (0.559 to 0.583 in.)


Minimum diameter:

14.0 mm (0.551 in.)


If the diameter is less than the minimum, replace the generator rotor assembly.