Home › Power Source / Network › 3ZR-FAE BATTERY / CHARGING › GENERATOR › from 2015.04
RM3090E _57 Power Source / Network _008394 3ZR-FAE BATTERY / CHARGING _0046853 GENERATOR A

3ZR-FAE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A183132N06
1.073,0.677 0.531,0.281 0.531,0.281 0.948,1.042 false 2.354,0.677 1.865,0.323 1.865,0.323 2.156,0.833 false 0.219,0.198 0.583,0.365 0.365,0.167 10 SST 1.573,0.24 1.958,0.427 0.385,0.188 10 SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A153389C05
1.708,0.088 1.871,0.234 0.164,0.146 10 *a 2.185,1.708 2.349,1.867 0.164,0.159 10 *b 2.732,1.363 2.392,1.795 false 2.732,1.363 2.392,1.795 false 2.392,1.795 2.753,1.335 false 2.735,0.864 1.909,0.182 false
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A314531C05
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new generator bearing cover packing to the generator coil assembly.

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A285303C05
2.635,0.563 2.917,0.167 2.917,0.167 3.083,0.167 true 1.188,0.688 0.833,0.333 0.833,0.333 0.667,0.333 true 0.521,0.25 0.833,0.406 0.313,0.156 10 false *a 3.104,0.083 3.417,0.24 0.313,0.156 10 false *a
*a Deep Socket Wrench (21 mm)


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


b.

Install the generator coil assembly with the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C14
2.469,0.813 1.958,0.198 1.958,0.198 1.708,0.198 true 0.896,0.531 0.583,0.188 0.583,0.188 0.333,0.188 false 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.49,0.115 1.802,0.271 0.313,0.156 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A284142C02
1.76,1.042 2.646,1.656 2.646,1.656 2.854,1.656 false 2.917,1.604 3.229,1.76 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 6.INSTALL GENERATOR TERMINAL INSULATOR

a.
A337510

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Make sure that the generator terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 8.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in a vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch by hand.


c.
A204357C14
0.333,0.667 1.833,0.167 1.833,0.167 1.781,0.938 true 1.25,1.417 1.25,0.938 true 1.5,1.833 1.667,1.833 1.667,1.833 2.167,1.167 true 1.188,1.417 1.5,1.573 0.313,0.156 10 false *a 1.865,0.052 2.635,0.25 0.771,0.198 10 false SST A 1.063,1.75 1.833,1.948 0.771,0.198 10 false SST B
*a Generator Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



d.
A229066C07
0.781,1.135 0.667,1.333 0.667,1.333 0.5,1.333 false 1.125,0.885 0.75,0.667 0.75,0.667 0.552,0.667 false 0.135,0.573 0.583,0.74 0.448,0.167 10 false SST B 0.063,1.26 0.542,1.417 0.479,0.156 10 false SST A 0.927,2.677 1.115,2.844 0.188,0.167 10 false *a 1.375,4.104 1.563,4.271 0.188,0.167 10 false *c 1.948,2.292 2.135,2.458 0.188,0.167 10 false *b
*a Hold
*b Torque Wrench Fulcrum Length
*c SST Fulcrum Length
V100135

Turn


Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):

64 N*m (653 kgf*cm, 47 ft.*lbf)




e.

Remove SST from the generator assembly.


f.

Check that the generator pulley with clutch rotates smoothly.


g.

Remove the generator assembly from a vice.


Hide 27416 9.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.