Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM J

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  Lack of Power or Hesitation  


DESCRIPTION

The VALVEMATIC system is able to continuously change the valve lift amount and valve timing. For engines equipped with a VALVEMATIC system, when a part such as a rocker arm in the camshaft housing has mechanical problems, the valve lift amount does not change and problems occur, such as a lack of engine power or rough idling.

CAUTION / NOTICE / HINT

A lack of engine power occurs when the throttle valve is malfunctioning or when there is a clog in the intake or exhaust system. Therefore, during the inspection, confirm that there are no clogs in any parts.

HINT:
·

When the throttle valve is malfunctioning, even if the accelerator pedal is fully depressed when the engine is running, the throttle does not fully open.

·

When there is a clog in the intake system, even if the accelerator pedal is fully depressed, the MAP is not the same as the atmospheric pressure.



When performing this inspection on a vehicle equipped with the VALVEMATIC, perform the following procedures first in order to confirm that there are no VVT system malfunctions.

1.

Perform the VVT system Active Test and confirm that the VVT follows the VVT target.

2.

If the VVT system Active Test results are normal, perform the VALVEMATIC system Active Test.


NOTICE:

When the vehicle is not equipped with the VALVEMATIC, even if the VVT system inspection (the inspection that checks if idling becomes unstable when changing the VVT to the most advanced and retarded positions through the Active Test) is performed, it cannot be determined that the malfunction is in the VVT system.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.PERFORM BASIC FUNCTION

B

2.PERFORM BASIC FUNCTION
a.

Check the air cleaner filter element sub-assembly.

HINT:

If the air cleaner filter element sub-assembly is dirty, clean or replace it.



b.

Check if there are any clogs in the intake or exhaust system.





f.

Measure the cylinder compression pressure (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

Result:
Result Proceed to
Everything normal A
Repaired problem area but malfunction reoccurs
Repaired problem area and malfunction does not reoccur B


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system, exhaust system, ignition system or engine assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




A

3.READ VALUE USING GTS

B

END

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Short FT #1, Long FT #1, AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Data List
Tester Display
AFS Voltage B1S1
O2S B1S2
Short FT #1
Long FT #1
50003 234 35,44,25,26

e.

Read the value while driving the vehicle.

Result:
Result Proceed to
No abnormal values in Data List A
Abnormal values in Data List B




A

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM (BANK 1))

B

CHECK FUEL SYSTEM

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM (BANK 1))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank1) / All Data / VVT Change Angle #1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the VVT System (Bank1)
Data List Display
VVT Change Angle #1
50004 234 112 305

e.

Read the value.

Result:
Result Proceed to
The "VVT Change Angle #1" value changes A
The "VVT Change Angle #1" value does not change B




A

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VALVEMATIC (ENG ON))

B

CHECK VVT SYSTEM

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VALVEMATIC (ENG ON))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VALVEMATIC (ENG ON) / All Data / MAP and VALVEMATIC Current Angle.

Powertrain > Engine and ECT > Active Test
Active Test Display
Activate the VALVEMATIC(ENG ON)
Data List Display
MAF
VALVEMATIC Current Angle
50004 234 165 3,162

e.

Maintain an engine speed of 3000 rpm with the shift lever in P or N (neutral) and the vehicle stationary.


f.

Read the value.

Standard:
GTS Operation Result
High VALVEMATIC Current Angle: 250 deg(CA) or more and shaft retracts
Low VALVEMATIC Current Angle: 100 to 120 deg(CA) and shaft extends


OK:

Change in MAP during the Active Test


HINT:
·

When the vehicle is driven while there is a malfunction in the VALVEMATIC system and the valve lift amount is fixed at the minimum, the vehicle speed cannot exceed 30 to 60 km/h (19 to 37 mph).

·

If the intake valve advance angle is within the VALVEMATIC operation prohibition range depending on the operating state of the VVT system, the Active Test "Activate the VALVEMATIC(ENG ON)" is prohibited. If the advance angle cannot be detected due to a malfunction in the VVT system, the Active Test "Activate the VALVEMATIC(ENG ON)" is prohibited.




Result:
Proceed to
OK
NG



OK

PERFORM SIMULATION TEST

NG

CHECK VALVEMATIC SYSTEM