Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051218 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


C278789N02
0.479,5.302 0.896,5.583 0.417,0.281 2.542,5.208 2.958,5.49 0.417,0.281 5.615,5.229 6.031,5.51 0.417,0.281 1.781,6.969 2.198,7.25 0.417,0.281 5.448,7.042 5.865,7.323 0.417,0.281 2.333,1.229 2.615,1.427 0.281,0.198 10 3B 3.01,0.938 3.292,1.135 0.281,0.198 10 3E 3.656,1.083 3.938,1.281 0.281,0.198 10 3C 4.344,1.208 4.625,1.406 0.281,0.198 10 3D 2.271,2.969 2.552,3.167 0.281,0.198 10 3A 0.604,5.365 0.885,5.563 0.281,0.198 10 3A 2.677,5.271 2.958,5.469 0.281,0.198 10 3B 5.729,5.292 6.01,5.49 0.281,0.198 10 3C 1.917,7.031 2.198,7.229 0.281,0.198 10 3D 5.573,7.104 5.854,7.302 0.281,0.198 10 3E

C278790C04
1.333,3.667 1.75,3.896 0.417,0.229 2.531,5.563 2.948,5.792 0.417,0.229 3.333,7.438 3.75,7.667 0.417,0.229 1.365,7.458 1.781,7.688 0.417,0.229 1.25,5.25 1.417,5.25 1.417,5.25 1.667,4.833 false 1.083,7.25 1.333,7.25 1.333,7.25 1.583,7 false 2.667,1.656 2.823,1.854 0.156,0.198 10 A 1.5,3.698 1.656,3.896 0.156,0.198 10 A 0.313,4.281 0.563,4.458 0.25,0.177 10 *A 1.083,5.167 1.333,5.344 0.25,0.177 10 *1 2.615,5.594 3.052,5.76 0.438,0.167 10 G78 3.406,7.469 3.865,7.635 0.458,0.167 10 G78 1.427,7.49 1.781,7.667 0.354,0.177 10 G79 0.917,7.167 1.167,7.344 0.25,0.177 10 *1 0.281,6.646 0.531,6.823 0.25,0.177 10 *B
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B Main Body ECU (Multiplex Network Body ECU) with 3 connectors
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (Multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A-11 (GND1) - Body ground - Ground Always Below 1 Ω
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Engine switch on (ACC) 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Engine switch off Below 1 V
A-32 (IG) - Body ground - Ignition power supply Engine switch on (IG) 11 to 14 V*1
10.5 to 14 V*2
A-32 (IG) - Body ground - Ignition power supply Engine switch off Below 1 V



d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

*3: w/ Panic Switch

*4: w/o Panic Switch

3E-1 (ACT-) - Body ground BR - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3E-1 (ACT-) - Body ground BR - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-5 (ACT-) - Body ground*4 B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-5 (ACT-) - Body ground*4 B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-4 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-4 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-3 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-3 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-10 (ACTD) - Body ground*3 B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-10 (ACTD) - Body ground*3 B - Body ground Door lock motor unlock drive output (all door) Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
3D-13 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-13 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-11 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3D-11 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3D-12 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3E-12 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
3E-17 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked Below 1 V
3D-17 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
3E-40 (FLCY) - Body ground W - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V
3E-40 (FLCY) - Body ground W - Body ground Front door LH courtesy light switch input Front door LH closed Pulse generation
G78-19 (FRCY) - Body ground L - Body ground Front door RH courtesy light switch input Front door RH open Below 1 V
G78-19 (FRCY) - Body ground L - Body ground Front door RH courtesy light switch input Front door RH closed Pulse generation
G78-1 (LCTY) - Body ground*3 W - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V
G78-1 (LCTY) - Body ground*3 W - Body ground Rear door LH courtesy light switch input Rear door LH closed Pulse generation
G78-24 (LCTY) - Body ground*4 W - Body ground*1
SB - Body ground*2
Rear door LH courtesy light switch input Rear door LH open Below 1 V
G78-24 (LCTY) - Body ground*4 W - Body ground*1
SB - Body ground*2
Rear door LH courtesy light switch input Rear door LH closed Pulse generation
G78-6 (RCTY) - Body ground Y - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V
G78-6 (RCTY) - Body ground Y - Body ground Rear door RH courtesy light switch input Rear door RH closed Pulse generation
G78-7 (LSFL) - Body ground B - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
G78-7 (LSFL) - Body ground B - Body ground Front door LH unlock detection switch input Front door LH locked Pulse generation
G78-18 (LSFR) - Body ground P - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
G78-18 (LSFR) - Body ground P - Body ground Front door RH unlock detection switch input Front door RH locked Pulse generation
3E-32 (LSR) - Body ground Y - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
3E-32 (LSR) - Body ground Y - Body ground Rear door RH unlock detection switch input Rear door RH and LH locked Pulse generation
3C-41 (LSR) - Body ground Y - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
3C-41 (LSR) - Body ground Y - Body ground Rear door LH unlock detection switch input Rear door LH and RH locked Pulse generation
3B-55 (BZR) - Body ground L - Body ground Wireless door lock buzzer signal Wireless door lock buzzer off Below 1 V
3B-55 (BZR) - Body ground L - Body ground Wireless door lock buzzer signal Wireless door lock buzzer on Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.

B264892N74
1.948,0.583 2.333,0.833 0.385,0.25 3.302,0.583 3.688,0.833 0.385,0.25 4.885,0.583 5.271,0.833 0.385,0.25 2.031,0.635 2.49,0.938 0.458,0.302 10 G82 3.385,0.635 3.854,0.927 0.469,0.292 10 G83 4.969,0.635 5.292,0.844 0.323,0.208 10 G84


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
G82-11 (E) - Body ground BR - Body ground Ground Always Below 1 Ω
G82-2 (+B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
G82-10 (CUTB) - Body ground P - Body ground Dark current cut fuse pin input signal Always 11 to 14 V


c.

Reconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G84-5 (IG) - G82-11 (E) LG - BR Engine switch power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
G83-6 (CSEL) - G82-11 (E) BR - BR Communication channel switching circuit Engine switch off and all door closed Below 1 V → 4.5 to 6.0 V → Below 1 V
G83-17 (RDAM) - G82-11 (E) Y - BR RF Signal input circuit Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed 11 to 14 V pulse generation at regular intervals → pulse generation
G83-5 (RCO) - G82-11 (E) V - BR Wireless tuner power supply output circuit Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed Below 1 V → 4.5 to 5.5 V



CHECK DOOR CONTROL RECEIVER


a.

Disconnect the M10 door control receiver connector.

B280754N14
3.406,0.24 3.76,0.448 0.354,0.208 3.469,0.26 3.76,0.406 0.292,0.146 10 M10


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the M10 door control receiver connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
M10-2 (CSEL) - M10-1 (GND) R - W-B Communication channel switching circuit Engine switch off and all door closed Below 1 V → 4.5 to 6.0 V → Below 1 V
M10-5 (DATA) - M10-1 (GND) Y - W-B Data output Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed Below 1 V → 10 to 16 V → Below 1 V
M10-4 (+5) - M10-1 (GND) V - W-B Battery (power supply) Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed Below 1 V → 4.5 to 5.5 V