Home › Drivetrain › K114F MULTIDRIVE / CVT › FRONT DIFFERENTIAL OIL SEAL(for RH Side) › from 2015.04
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172323 FRONT DIFFERENTIAL OIL SEAL(for RH Side) A

K114F MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 43410M 2.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C295672C01
1.25,0.25 1.635,0.25 1.635,0.25 2.354,0.854 false 1.073,0.188 1.385,0.385 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with protective tape wound around the tip, pry out the front drive shaft oil seal RH.

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 30400B 3.REMOVE CVT TYPE T OIL SEAL

C295673N01
1.583,1.094 1.156,0.458 1.156,0.458 0.75,0.469 false 1.063,3 1.854,3 1.854,3 1.854,2.719 false 0.427,0.385 0.885,0.583 0.458,0.198 10 false SST 0.74,2.917 1.198,3.115 0.458,0.198 10 false SST

a.

Using SST, remove the CVT type T oil seal from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 30400B 4.INSTALL CVT TYPE T OIL SEAL

a.

Apply MP grease to the lip of a new CVT type T oil seal.


b.
C295674C01
1.229,1.76 1.219,1.146 false 1.229,1.563 1.531,1.563 1.531,1.563 1.521,1.083 false 2.844,0.365 3.156,0.563 0.313,0.198 10 false *a 1.125,1.802 1.583,2 0.458,0.198 10 false SST
*a 21.5 to 22.5 mm (0.847 to 0.885 in.)


Using SST and a hammer, install the CVT type T oil seal to the continuously variable transaxle assembly.

SST
09950-60010  (09951-00390)
09950-70010  (09951-07200)

Standard depth:

21.5 to 22.5 mm (0.847 to 0.885 in.)


NOTICE:

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Apply MP grease to the lip of a new front drive shaft oil seal RH.


b.
C295675C03
1.385,1.667 1.115,1.667 1.115,1.667 1.115,1.104 false 2.667,1.75 2.979,1.948 0.313,0.198 10 false *a 1.448,1.573 1.906,1.771 0.458,0.198 10 false SST
*a 5.5 to 6.5 mm (0.217 to 0.255 in.)


Using SST and a hammer, install the front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09515-87302  

Standard depth:

5.5 to 6.5 mm (0.217 to 0.255 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 36100 6.INSTALL TRANSFER ASSEMBLY