Home › Drivetrain › K114F MULTIDRIVE / CVT › SHIFT PADDLE SWITCH › from 2015.04
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172321 SHIFT PADDLE SWITCH G

K114F MULTIDRIVE / CVT  SHIFT PADDLE SWITCH  INSPECTION  


PROCEDURE

Hide 84610F 1.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY

C279463C01
1.292,3.344 1.063,3.031 true 0.823,3.344 0.927,3.021 true 2.771,3.354 2.667,2.938 true 2.25,3.354 2.51,2.938 true 0.365,3.344 0.792,3.031 true 0.708,3.719 1.021,3.875 0.313,0.156 10 *a 2.49,3.729 2.802,3.885 0.313,0.156 10 *b 0.104,0.063 0.417,0.219 0.313,0.156 10 *c 0.198,3.375 0.625,3.563 0.427,0.188 10 ECC1 0.667,3.375 1,3.542 0.333,0.167 10 ECC 1.146,3.385 1.552,3.563 0.406,0.177 10 SFTD 2.073,3.385 2.5,3.563 0.427,0.177 10 SFTU 2.635,3.385 2.979,3.563 0.344,0.177 10 ECC
*a for LH
*b for RH
*c Component without wire harness connected
(Transmission Shift Switch Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Shift Position Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC1 "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTD - ECC1 "-" shift paddle not operated (down-shift) 1 MΩ or higher

for RH
Tester Connection Shift Position Specified Condition
SFTU - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTU - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher


If the result is not as specified, replace the transmission shift switch assembly.


Hide 84523 2.INSPECT NO. 1 SWITCH WIRE

a.

Connect the No. 1 switch wire connector to the transmission shift switch assembly.


b.

Disconnect the steering pad switch connector from the No. 1 switch wire.


c.
C279491C03
1.792,1.135 2.24,0.938 true 1.792,1.344 2.219,1.552 true 1.635,1.135 1.146,0.948 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 0.76,0.854 1.375,1.052 0.615,0.198 10 SFTU 2.302,0.854 2.917,1.052 0.615,0.198 10 SFTD 2.292,1.49 2.906,1.688 0.615,0.198 10 ECC
*a Component without wire harness connected
(No. 1 Switch Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTU - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTU - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher