Home › Engine / Hybrid System › 3ZR-FAE STARTING › STARTER(w/ Stop And Start System) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _008393 3ZR-FAE STARTING _0166447 STARTER(w/ Stop And Start System) A

3ZR-FAE STARTING  STARTER(w/ Stop And Start System)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE WIRE HARNESS

a.
A323617

Remove the 2 nuts and wire harness from the starter assembly.


Hide 2.REMOVE HARNESS

a.
A314228

Remove the 2 harness connectors to remove the harness from the starter assembly.


Hide 3.REMOVE STARTER INRUSH CURRENT REDUCTION RELAY

a.
A323625

Remove the nut and disconnect the lead wire from the terminal M.


b.

Remove the 2 bolts and starter inrush current reduction relay.


Hide 28226B 4.REMOVE REPAIR SERVICE STARTER KIT

a.
A314231

Holding the repair service starter kit to the starter drive housing assembly, remove the 2 nuts.


b.
A323598C05
0.479,1.823 0.667,1.823 0.667,1.823 0.979,0.625 true 1.49,0.125 1.656,0.125 1.656,0.125 1.708,0.448 false 2.292,0.24 2.135,0.24 2.135,0.24 1.969,0.51 false 0.302,1.74 0.615,1.896 0.313,0.156 10 false *1 2.344,0.125 2.542,0.292 0.198,0.167 10 true *2 1.323,0.021 1.635,0.219 0.313,0.198 10 false *a
*1 Pinion Drive Lever
*2 Plunger
*a Hook


While lifting the front of the repair service starter kit, remove the hook from the pinion drive lever, then remove the repair service starter kit.

NOTICE:

Do not drop the plunger when removing the repair service starter kit.



Hide 28120 5.REMOVE STARTER YOKE ASSEMBLY

a.
A314233

Using a T25 "TORX" socket wrench, remove the 2 bolts.


b.
A314234

Remove the starter yoke assembly together with the starter commutator end frame assembly from the starter drive housing assembly.


Hide 28130 6.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A187214

Remove the 2 screws.


b.
A187221

Remove the starter commutator end frame assembly from the starter yoke assembly.

NOTICE:

while holding down the lead wire, remove the starter commutator end frame assembly.



Hide 28140 7.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C06
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Spring
*b Brush


Using a screwdriver, hold the spring back and disconnect the 4 brushes.


b.

Remove the starter brush holder assembly.


Hide 28160 8.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438

Remove the starter armature assembly from the starter yoke assembly.


Hide 9.REMOVE STARTER ARMATURE PLATE

a.
A314235C04
0.979,2.01 1.177,2.01 1.177,2.01 1.375,1.583 true 1.844,1.927 2,1.927 2,1.927 2.24,1.438 true 2.667,0.802 2.51,0.417 2.51,0.417 2.313,0.417 true 0.854,0.542 0.708,0.219 0.708,0.219 0.51,0.219 true 0.292,0.177 0.604,0.333 0.313,0.156 10 false *1 2.083,0.354 2.396,0.51 0.313,0.156 10 false *2 1.646,1.875 1.958,2.031 0.313,0.156 10 false *3 0.74,1.958 1.052,2.115 0.313,0.156 10 false *3
*1 Starter Drive Housing Assembly
*2 Starter Yoke Assembly
*3 Starter Armature Plate


Remove the starter armature plate from the starter drive housing assembly or starter yoke assembly.


Hide 10.REMOVE PLANETARY GEAR

a.
A314236

Remove the 3 planetary gears from the starter center bearing clutch sub-assembly.


Hide 28021 11.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A314237C04
2.854,0.74 2.99,0.375 2.99,0.375 3.115,0.375 false 2.01,0.354 2.177,0.146 2.177,0.146 2.302,0.146 false 2.448,1.375 2.656,1.198 2.656,1.198 2.781,1.198 false 3.198,0.302 3.427,0.469 0.229,0.167 10 false *1 2.375,0.083 2.688,0.24 0.313,0.156 10 false *2 2.865,1.156 3.177,1.313 0.313,0.156 10 false *3
*1 Rubber Seal
*2 Pinion Drive Lever
*3 Starter Center Bearing Clutch Sub-assembly


Remove the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal from the starter drive housing assembly.


b.

Remove the pinion drive lever and rubber seal from the starter center bearing clutch sub-assembly.