Home › Engine / Hybrid System › 3ZR-FAE STARTING › STARTER(w/ Stop And Start System) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _008393 3ZR-FAE STARTING _0166447 STARTER(w/ Stop And Start System) A

3ZR-FAE STARTING  STARTER(w/ Stop And Start System)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A314239C03
1.854,0.458 1.729,0.115 1.729,0.115 1.615,0.115 false 2.885,0.729 3,0.448 3,0.448 3.125,0.448 false 2.615,1.583 2.802,1.333 2.802,1.333 2.927,1.333 false 0.469,1.594 0.604,1.927 0.604,1.927 0.823,1.927 false 3.198,0.344 3.427,0.5 0.229,0.156 10 false *3 1.427,0.021 1.74,0.177 0.313,0.156 10 false *2 2.99,1.271 3.302,1.427 0.313,0.156 10 false *1 0.906,1.823 1.219,2.021 0.313,0.198 10 false *4
*1 Starter Center Bearing Clutch Sub-assembly
*2 Pinion Drive Lever
*3 Rubber Seal
*4 Starter Drive Housing Assembly
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever as shown in the illustration.


b.

Install the pinion drive lever and rubber seal to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal to the starter drive housing assembly.


Hide 2.INSTALL PLANETARY GEAR

a.
A314240C02
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter center bearing clutch sub-assembly.


b.

Install the 3 planetary gears to the starter center bearing clutch sub-assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A202439

Install the starter armature assembly to the starter yoke assembly.


Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A211303

Hold the brush spring back and install the 4 brushes to the starter brush holder assembly.


b.
A211304

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes.


c.
A314282C02
1.396,0.219 1.552,0.219 1.552,0.219 2.458,0.771 true 2.51,0.563 2.938,0.156 2.938,0.156 3.073,0.156 true 2.167,1.542 2.302,1.542 2.302,1.542 2.51,0.958 true 1.208,0.104 1.521,0.26 0.313,0.156 10 false *a 3.146,0.063 3.375,0.219 0.229,0.156 10 false *b 1.99,1.438 2.302,1.594 0.313,0.156 10 false *c
*a Grommet
*b Negative (-) Brush Holder Plate
*c Positive (+) Motor Lead Wire


Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A209964C03
1.885,0.24 2.052,0.24 2.052,0.24 2.219,0.396 false 1.25,2.01 1.51,2.01 1.51,2.01 2.031,1.208 true 0.469,1.813 0.635,1.813 0.635,1.813 1.198,0.885 true 0.281,1.719 0.594,1.875 0.313,0.156 10 false *a 1.083,1.906 1.396,2.104 0.313,0.198 10 false *b 1.729,0.125 2.042,0.281 0.313,0.156 10 false *a
*a Lead Wire Rubber
*b Cutout


Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

Align the lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.



b.

Install the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.
A204351C06
3.021,1.448 2.865,1.448 2.865,1.448 2.531,1.885 false 1.552,1.531 1.552,1.875 false 2.458,0.865 2.271,0.865 2.271,0.865 1.865,1.313 false 1.906,0.26 1.719,0.26 1.719,0.26 1.448,0.625 false 3.104,0.792 2.948,0.792 2.948,0.792 2.615,1.229 false 3.167,0.688 3.427,0.927 0.26,0.24 10 false *2 2.51,0.75 2.792,0.969 0.281,0.219 10 false *a 1.958,0.156 2.271,0.354 0.313,0.198 10 false *1 3.063,1.333 3.375,1.531 0.313,0.198 10 false *b 1.5,1.896 1.781,2.115 0.281,0.219 10 false *a
*1 Starter Yoke Assembly
*2 Starter Armature Plate
*a Stopper
*b Protrusion


Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

NOTICE:

Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A314241C03
2.698,1.719 2.698,1.375 true 1.771,1.917 1.771,1.573 false 1.167,0.792 0.906,0.281 0.906,0.281 0.635,0.281 false 1.833,0.323 2.323,0.323 false 1.646,0.219 1.958,0.417 0.313,0.198 10 false *2 1.708,1.938 2.021,2.135 0.313,0.198 10 false *a 0.438,0.167 0.75,0.365 0.313,0.198 10 false *1 2.656,1.76 2.969,1.958 0.313,0.198 10 false *b
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*a Cutout
*b Protrusion


Install the starter yoke assembly to the starter drive housing assembly.

NOTICE:

Align the cutout of the starter yoke assembly with the protrusion of the starter drive housing assembly.



b.

Install the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226B 8.INSTALL REPAIR SERVICE STARTER KIT

A323615C04
1.792,0.896 2,0.427 2,0.427 2.219,0.427 false 0.865,1.833 1.094,1.833 1.094,1.833 1.396,1.51 false 2.74,2.052 2.5,2.052 2.5,2.052 2.302,1.771 false 2.396,2.625 2.156,2.625 2.156,2.625 2.021,3.083 false 2.615,2.792 2.375,2.792 2.375,2.792 2.25,3.146 false 3.125,3.938 3.01,4.281 3.01,4.281 2.781,4.281 false 0.948,3.135 0.729,4.313 0.729,4.313 0.5,4.313 true 1.646,3.01 1.427,3.365 1.427,3.365 1.26,3.365 true 1.865,3.177 1.563,3.594 1.563,3.594 1.406,3.594 true 2.156,2.479 1.917,2.479 1.917,2.479 1.781,2.938 false 0.323,4.208 0.635,4.365 0.313,0.156 10 false *1 1.219,3.5 1.469,3.74 0.25,0.24 10 false *2 2.708,2.729 3.021,2.885 0.313,0.156 10 false *3 1.073,3.25 1.26,3.438 0.188,0.188 10 true *c 2.573,4.208 2.885,4.365 0.313,0.156 10 false *4 0.688,1.729 1,1.885 0.313,0.156 10 false *5 2.458,2.521 2.781,2.708 0.323,0.188 10 false *a 2.292,0.333 2.604,0.49 0.313,0.156 10 false *b 0.76,0.396 1.073,0.552 0.313,0.156 10 false 90° 2.813,1.948 3.125,2.104 0.313,0.156 10 false *4 2.229,2.385 2.677,2.625 0.448,0.24 10 false *5
*1 Pinion Drive Lever
*2 Plunger
*3 Return Spring
*4 Magnet Switch
*5 Plunger Cover
*a Protrusion
*b Ventilation Hole
*c Hook


a.

Hang the hook of the plunger on the pinion drive lever and install the repair service starter kit.

NOTICE:
·

Make sure the return spring is not resting on the protrusion of the plunger or pushed between the magnet switch and plunger.

·

Install the plunger cover so that the ventilation hole is positioned as shown in the illustration.




b.

Install the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 9.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

a.

Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


b.

Connect the lead wire to terminal M with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 10.INSTALL HARNESS

a.

Connect the 2 harness connectors to install the harness.


Hide 11.INSTALL WIRE HARNESS

a.

Install the wire harness to the starter assembly with the 2 nuts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)