Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B411439E01
0.573,0.396 3.177,0.594 2.604,0.198 10 false to IG1 NO.1 Relay 0.906,0.885 3.156,1.104 2.25,0.219 10 false to IG2 Relay 0.865,1.365 3.115,1.583 2.25,0.219 10 false to ACC Relay 0.938,2.323 3.188,2.542 2.25,0.219 10 false from Battery 3.563,2.01 5.656,2.24 2.094,0.229 10 false AM2 0.927,1.833 3.177,2.052 2.25,0.219 10 false from Battery 3.385,2.5 5.479,2.729 2.094,0.229 10 false ECU-B NO.1 0.667,4.813 2.76,5.042 2.094,0.229 10 false M10 0.667,4.969 2.76,5.198 2.094,0.229 10 false Door Control Receiver 5.552,4.875 7.156,5.365 1.604,0.49 10 false Certification ECU (Smart Key ECU Assembly) 5.854,0.417 7.156,0.708 1.302,0.292 10 false IG1D 5.854,0.917 7.156,1.208 1.302,0.292 10 false IG2D 5.854,1.396 7.156,1.688 1.302,0.292 10 false ACCD 5.854,1.844 7.156,2.135 1.302,0.292 10 false +B 5.854,2.354 7.156,2.646 1.302,0.292 10 false CUTB 5.531,0.417 7.156,0.635 1.625,0.219 10 false G84 5.531,0.906 7.156,1.125 1.625,0.219 10 false G82 5.531,1.385 7.156,1.604 1.625,0.219 10 false G84 5.531,1.854 7.156,2.073 1.625,0.219 10 false G82 5.531,2.344 7.156,2.563 1.625,0.219 10 false G82 5.531,3.146 7.156,3.365 1.625,0.219 10 false G83 5.531,3.583 7.156,3.802 1.625,0.219 10 false G83 5.531,4.021 7.156,4.24 1.625,0.219 10 false G83 5.531,4.448 7.156,4.667 1.625,0.219 10 false G82 5.573,4.281 7.156,4.5 1.583,0.219 10 false 11 5.573,3.833 7.156,4.052 1.583,0.219 10 false 6 5.573,3.396 7.156,3.615 1.583,0.219 10 false 17 5.615,2.927 7.156,3.146 1.542,0.219 10 false 5 5.615,1.667 7.156,1.885 1.542,0.219 10 false 2 5.615,1.177 7.156,1.396 1.542,0.219 10 false 4 5.615,0.729 7.156,0.948 1.542,0.219 10 false 9 5.615,0.208 7.156,0.427 1.542,0.219 10 false 6 5.573,2.146 7.156,2.365 1.583,0.219 10 false 10 5.854,3.146 7.156,3.438 1.302,0.292 10 false RCO 5.854,3.573 7.156,3.865 1.302,0.292 10 false RDAM 5.854,4.031 7.156,4.323 1.302,0.292 10 false CSEL 5.854,4.448 7.156,4.74 1.302,0.292 10 false E 1.469,4.427 2.771,4.719 1.302,0.292 10 false GND 1.406,4.031 2.708,4.323 1.302,0.292 10 false CSEL 1.396,3.573 2.698,3.865 1.302,0.292 10 false DATA 1.573,3.146 2.875,3.438 1.302,0.292 10 false +5 1.885,3 3.177,3.219 1.292,0.219 10 false 4 1.885,3.417 3.177,3.635 1.292,0.219 10 false 5 1.885,3.875 3.177,4.094 1.292,0.219 10 false 2 1.885,4.313 3.177,4.531 1.292,0.219 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First, inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

DTC is output

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
Door locks operate normally
Door locks do not operate



Door locks operate normally

4.CHECK KEY DIAGNOSTIC MODE

Door locks do not operate

4.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B340881C04
2.25,1.146 2.563,1.344 0.313,0.198 10 *a 0.073,0.052 0.385,0.25 0.313,0.198 10 *A
*A for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


B340882C05
0.135,0.073 0.448,0.271 0.313,0.198 10 *A 1.396,1.135 1.708,1.333 0.313,0.198 10 *a
*A for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B340882C05
0.135,0.073 0.448,0.271 0.313,0.198 10 *A 1.396,1.135 1.708,1.333 0.313,0.198 10 *a
*A for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


B340881C04
2.25,1.146 2.563,1.344 0.313,0.198 10 *a 0.073,0.052 0.385,0.25 0.313,0.198 10 *A
*A for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B340886C02
0.656,1.156 2.25,0.323 2.25,0.323 2.458,0.313 false 1.75,1.167 2.24,0.323 false 2.542,0.229 2.854,0.427 0.313,0.198 10 *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iv.
B340887C02
0.677,1.063 2.375,0.281 2.375,0.281 2.563,0.281 false 1.708,1.073 2.375,0.281 false 2.625,0.208 2.854,0.417 0.229,0.208 10 *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

v.
B340888C02
1.792,1.229 2.104,1.427 0.313,0.198 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
OK:

Wireless door lock buzzer sounds.




Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

10.CHECK WAVE ENVIRONMENT

C

11.CHECK WAVE ENVIRONMENT
5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

7.CHECK ENTRY DOOR LOCK OPERATION
6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK ENTRY DOOR LOCK OPERATION
7.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

8.CHECK TRANSMITTER BATTERY

NG

10.CHECK WAVE ENVIRONMENT
8.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)


Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

10.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
11.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

B264896C42
4.729,0.885 5.125,1.125 0.396,0.24 2.115,0.885 2.51,1.125 0.396,0.24 4.385,1.625 4.125,2.292 false 1.979,1.74 1.76,2.292 false 4.542,1.615 4.698,2.302 false 0.302,0.292 0.49,0.448 0.188,0.156 10 *a 4.802,0.938 5.094,1.094 0.292,0.156 10 G84 2.188,0.927 2.479,1.083 0.292,0.156 10 G82 3.948,2.333 4.313,2.49 0.365,0.156 10 IG1D 1.531,2.313 1.896,2.469 0.365,0.156 10 IG2D 4.573,2.333 5.031,2.49 0.458,0.156 10 ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Power Source Control / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON ALL OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) (ACC relay on)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

g.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G84-6 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
G82-9 (IG2D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
G84-4 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 9 V or higher
Engine switch on (ACC) 9 V or higher


HINT:

Using the GTS, measure the voltage while confirming the power source mode on the Data List.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.READ VALUE USING GTS (IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ignition Switch Engine switch on (IG) ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
·

Displays whether the IG power source signal input is on or off.

·

Use this Data List item to help determine the cause when all entry and start system /wireless functions do not operate.

·

If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal, the engine switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the L code stored in the certification ECU (smart key ECU assembly) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered on (IG) at that time.


Body Electrical > Entry&Start > Data List
Tester Display
Ignition Switch
50003 125 18
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (ACC SW, IG SW)

NG

CHECK RELAY CONTACT SIDE CIRCUIT

14.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch status ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
"ON" is also displayed for this item when the engine switch is on (IG)
IG SW Engine switch status ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"OFF" is also displayed for this item when the engine switch is on (ACC)
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)

NG

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
a.
B274828C07
1.49,0.104 1.927,0.375 0.438,0.271 1.156,1.271 0.854,1.802 false 2.302,1.135 2.792,1.771 false 2.333,0.948 2.781,0.729 false 1.604,0.156 2.104,0.458 0.5,0.302 10 G82 0.156,0.073 0.438,0.25 0.281,0.177 10 *a 0.813,1.802 1.167,1.979 0.354,0.177 10 E 2.802,0.635 3.156,0.813 0.354,0.177 10 +B 2.625,1.792 3.063,1.969 0.438,0.177 10 CUTB
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-10 (CUTB) - Body ground Always 11 to 14 V
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M10 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-5 (RCO) - M10-4 (+5) Always Below 1 Ω
G83-17 (RDAM) - M10-5 (DATA) Always Below 1 Ω
G83-6 (CSEL) - M10-2 (CSEL) Always Below 1 Ω
G83-5 (RCO) or M10-4 (+5) - Body ground Always 10 kΩ or higher
G83-17 (RDAM) or M10-5 (DATA) - Body ground Always 10 kΩ or higher
G83-6 (CSEL) or M10-2 (CSEL) - Body ground Always 10 kΩ or higher



d.

Connect the G83 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

17.CHECK DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK DOOR CONTROL RECEIVER
a.
B274836C51
1.51,0.24 1.938,0.5 0.427,0.26 2.042,1.125 2.448,1.542 false 1.625,0.292 2.135,0.479 0.51,0.188 10 M10 2.531,1.5 3.021,1.865 0.49,0.365 10 GND 0.219,0.188 0.646,0.458 0.427,0.271 10 *a
*a Component with harness connected
(Door Control Receiver)


Connect the door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274836C58
1.51,0.24 1.938,0.5 0.427,0.26 2.042,1.125 2.448,1.542 false 1.854,1.135 2.167,1.823 false 1.552,1.156 0.885,1.531 false 1.625,0.292 2.135,0.479 0.51,0.188 10 false M10 2.531,1.5 3.021,1.865 0.49,0.365 10 false GND 0.219,0.188 0.646,0.458 0.427,0.271 10 false *a 0.656,1.427 1.146,1.635 0.49,0.208 10 false +5 2.021,1.865 2.51,2.073 0.49,0.208 10 false CSEL
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M10-4 (+5) - M10-1 (GND)
Procedure
·

Engine switch off

·

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure
·

Engine switch off

·

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V
M10-2 (CSEL) - M10-1 (GND) Engine switch off and all doors closed Below 1 V → 4.4 to 6.5 V → Below 1 V



Result:
Proceed to
OK
NG



OK

19.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.CHECK DOOR CONTROL RECEIVER
a.
B274836C53
1.51,0.24 1.938,0.5 0.427,0.26 2.042,1.125 2.448,1.542 false 1.375,1.125 0.854,1.51 false 1.625,0.292 2.135,0.479 0.51,0.188 10 M10 2.531,1.5 3.021,1.865 0.49,0.365 10 GND 0.219,0.188 0.646,0.458 0.427,0.271 10 *a 0.5,1.448 0.99,1.813 0.49,0.365 10 DATA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M10-5 (DATA) - M10-1 (GND)
Procedure
·

All doors closed

·

All doors locked

·

Electrical key transmitter sub-assembly switch pressed


Below 1 V → 10 to 16 V → Below 1 V



Result:
Proceed to
OK
NG



OK

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
21.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.

Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B




A

23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

24.CHECK WAVE ENVIRONMENT
23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

24.CHECK WAVE ENVIRONMENT
24.CHECK WAVE ENVIRONMENT
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M10 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-2 (CSEL) - G83-6 (CSEL) Always Below 1 Ω
M10-2 (CSEL) or G83-6 (CSEL) - Body ground Always 10 kΩ or higher



d.

Connect the G83 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274836C54
1.51,0.24 1.938,0.5 0.427,0.26 2.042,1.125 2.448,1.542 false 1.833,1.146 1,1.635 false 1.625,0.292 2.135,0.479 0.51,0.188 10 M10 2.531,1.5 3.021,1.865 0.49,0.365 10 GND 0.219,0.188 0.646,0.458 0.427,0.271 10 *a 0.604,1.573 1.094,1.938 0.49,0.365 10 CSEL
*a Component with harness connected
(Door Control Receiver)


Connect the M10 door control receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M10-2 (CSEL) - M10-1 (GND) Engine switch off and all doors closed Below 1 V → 4.5 to 6 V → Below 1 V



Result:
Proceed to
OK
NG



OK

27.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

27.CHECK DOOR CONTROL RECEIVER
a.
B274836C53
1.51,0.24 1.938,0.5 0.427,0.26 2.042,1.125 2.448,1.542 false 1.375,1.125 0.854,1.51 false 1.625,0.292 2.135,0.479 0.51,0.188 10 M10 2.531,1.5 3.021,1.865 0.49,0.365 10 GND 0.219,0.188 0.646,0.458 0.427,0.271 10 *a 0.5,1.448 0.99,1.813 0.49,0.365 10 DATA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


Standard Voltage:
Tester Connection Condition Specified Condition
M10-5 (DATA) - M10-1 (GND)
Procedure
·

All doors closed

·

All doors locked

·

Electrical key transmitter sub-assembly switch pressed*


Below 1 V → 10 to 16 V → Below 1 V


*: While the electrical key antennas are being inspected in key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)