When the glass breakage sensor detects that the back door glass, rear door quarter window glass LH or RH is tapped or broken, the sensor will set off the alarm for 30 seconds.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sealed Glas Brak Sen | Glass breakage sensor connecting | With or Without | With: Glass breakage sensor connected
Without: Glass breakage sensor not connected |
- |
| Tester Display |
|---|
| Sealed Glas Brak Sen |
"With" (glass breakage sensor operating) appears on GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Connect the instrument panel junction block assembly connectors.
Disconnect the M16, N10, U2 and B glass breakage sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-19 (GPBS) - M16-2 (SSR+) | Always | Below 1 Ω |
| M16-1 (SSR-) - N10-2 (SSR+) | Always | Below 1 Ω |
| N10-1 (SSR-) - U2-2 (SSR+) | Always | Below 1 Ω |
| B-1 (E) - Body ground | Always | Below 1 Ω |
| A-19 (GPBS) - Body ground | Always | 10 kΩ or higher |
| M16-2 (SSR+) - Body ground | Always | 10 kΩ or higher |
| M16-1 (SSR-) - Body ground | Always | 10 kΩ or higher |
| N10-2 (SSR+) - Body ground | Always | 10 kΩ or higher |
| N10-1 (SSR-) - Body ground | Always | 10 kΩ or higher |
| U2-2 (SSR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M16 rear door quarter window glass RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SSR+) - 1 (SSR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N10 rear door quarter window glass LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SSR+) - 1 (SSR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U2 and B back door glass connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 (SSR+) - B-1 (E) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Disconnect the M16 glass breakage sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-38 (GCS) - M16-2 (SSR+) | Always | Below 1 Ω |
| 3D-38 (GCS) - Body ground | Always | 10 kΩ or higher |
| M16-2 (SSR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG