Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.04–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (malfunction in CAN communication with the acceleration sensor) is output.

These DTCs are also output when calibration has not been completed.

DTC C1279 can be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or the Test Mode ends. DTC C1279 is output only in the Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1232 Acceleration Sensor Stuck Malfunction At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit


C1243 Acceleration Sensor Stuck Malfunction While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change 0.0294 G or more occurs 16 times or more.
·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit


C1245 Acceleration Sensor Output Malfunction At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit

·

Sensor installation


C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Acceleration sensor (Airbag sensor assembly)

·

Sensor installation



WIRING DIAGRAM

C240027E06
4.99,3.5 6.667,3.813 1.677,0.313 10 Skid Control ECU (Brake Actuator Assembly) 0.719,4.167 2.396,4.344 1.677,0.177 10 : CAN Communication Line 2.823,1.896 3.094,2.052 0.271,0.156 10 A/B 0.958,1.75 1.229,1.906 0.271,0.156 10 IG2 1.271,1.635 1.448,1.792 0.177,0.156 10 21 1.271,2.594 1.448,2.75 0.177,0.156 10 26 1.271,2.208 1.448,2.365 0.177,0.156 10 25 1,2.698 1.198,2.854 0.198,0.156 10 E2 1,2.333 1.198,2.49 0.198,0.156 10 E1 0.021,3.375 2.219,3.729 2.198,0.354 10 Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.021,3.198 0.292,3.375 0.271,0.177 10 G92 4.958,3.302 5.417,3.5 0.458,0.198 10 A64

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).

K111: Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K111F: Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K114F: Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



HINT:

When U0124 and/or U0126 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.



d.

Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210) or for zero point calibration of the acceleration sensor undone (C1336) are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC (relating to yaw rate and acceleration sensor) is output A
DTC (relating to CAN communication system) is output (for LHD) B
DTC (relating to CAN communication system) is output (for RHD) C
DTC (C1210 and/or C1336) are output D




A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

D

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the airbag sensor assembly has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted position.



Result:
Proceed to
OK
NG



OK

NG