Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › THROTTLE BODY › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0046857 THROTTLE BODY A

3ZR-FAE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 22210 1.INSTALL THROTTLE BODY ASSEMBLY

a.

Install a new gasket to the intake manifold.


b.

for Type A:

Install the throttle body assembly with the 2 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



c.

for Type B:

Install the throttle body assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



d.

Connect the water by-pass hose and No. 2 water by-pass hose, and slide the 2 clamps to secure them.


e.

Connect the throttle body assembly connector.


Hide 17705 2.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.
A302253

Install the air cleaner cap sub-assembly. Then, release the lock of the air cleaner cap sub-assembly clamp to secure the clamp.


b.

Connect the PCV hose to the cylinder head cover sub-assembly, and slide the clamp to secure it.


c.

Connect the 2 clamps.


d.

Attach the wire harness to the air cleaner cap sub-assembly.


e.

Connect the mass air flow meter connector.


Hide 11212 3.INSTALL NO. 2 CYLINDER HEAD COVER

a.

Attach the 4 clips to install the No. 2 cylinder head cover.

NOTICE:
·

Be sure to attach the clips securely.

·

Do not apply excessive force or hit the No. 2 cylinder head cover to attach the clips. This may cause the No. 2 cylinder head cover to break.




Hide 51441 6.INSTALL NO. 1 ENGINE UNDER COVER

Hide 7. PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after reassembling the throttle body assembly or removing and reinstalling any throttle body component.

·

Perform the following procedure after replacing the ECM, throttle body assembly or any throttle body components. The following procedure should also be performed if the throttle body assembly is cleaned.

·

Be sure to perform this procedure after replacing the ECM and reconnecting the battery cable.



a.

Disconnect the EFI MAIN and ETCS fuses at the same time. Wait at least 60 seconds, and then reconnect the fuses.


b.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above steps again.



c.

Connect the GTS to the DLC3 and clear the DTCs.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR


d.

Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Standard Idle Speed:
Item Specified Condition
for Manual Transaxle 580 to 680 rpm
for CVT 680 to 780 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in neutral (for Manual Transaxle), or N or P (for CVT).




e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Sensor Position
50003 234 12

f.

Perform a road test and confirm that there are no abnormalities.