Home › Engine / Hybrid System › 3ZR-FAE STARTING › RELAY › 2015.04–2016.08
RM3090E _51 Engine / Hybrid System _008393 3ZR-FAE STARTING _0046850 RELAY G

3ZR-FAE STARTING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST) (w/o Stop And Start System)

a.
A188757N06
2.708,0.573 2.833,0.208 2.833,0.208 3.052,0.208 false 2.135,0.563 2,0.208 2,0.208 1.771,0.208 false 2.646,1.115 3.063,1.115 false 2.646,1.604 3.063,1.604 false 1.646,0.125 1.802,0.323 0.156,0.198 10 1 3.115,0.135 3.271,0.333 0.156,0.198 10 2 3.125,1.031 3.281,1.229 0.156,0.198 10 5 3.115,1.51 3.271,1.708 0.156,0.198 10 3 0.313,1.25 0.469,1.448 0.156,0.198 10 1 0.313,0.771 0.469,0.969 0.156,0.198 10 3 1.323,0.771 1.479,0.969 0.156,0.198 10 5 1.323,1.271 1.479,1.469 0.156,0.198 10 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter relay.


Hide 28300 2.INSPECT STARTER NO. 1 RELAY (ST NO. 1) (w/ Stop And Start System)

a.
A188757N06
2.708,0.573 2.833,0.208 2.833,0.208 3.052,0.208 false 2.135,0.563 2,0.208 2,0.208 1.771,0.208 false 2.646,1.115 3.063,1.115 false 2.646,1.604 3.063,1.604 false 1.646,0.125 1.802,0.323 0.156,0.198 10 1 3.115,0.135 3.271,0.333 0.156,0.198 10 2 3.125,1.031 3.281,1.229 0.156,0.198 10 5 3.115,1.51 3.271,1.708 0.156,0.198 10 3 0.313,1.25 0.469,1.448 0.156,0.198 10 1 0.313,0.771 0.469,0.969 0.156,0.198 10 3 1.323,0.771 1.479,0.969 0.156,0.198 10 5 1.323,1.271 1.479,1.469 0.156,0.198 10 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter No. 1 relay.


Hide 28300 3.INSPECT STARTER NO. 2 RALAY (ST NO. 2) (w/ Stop And Start System)

a.
A188757N06
2.708,0.573 2.833,0.208 2.833,0.208 3.052,0.208 false 2.135,0.563 2,0.208 2,0.208 1.771,0.208 false 2.646,1.115 3.063,1.115 false 2.646,1.604 3.063,1.604 false 1.646,0.125 1.802,0.323 0.156,0.198 10 1 3.115,0.135 3.271,0.333 0.156,0.198 10 2 3.125,1.031 3.281,1.229 0.156,0.198 10 5 3.115,1.51 3.271,1.708 0.156,0.198 10 3 0.313,1.25 0.469,1.448 0.156,0.198 10 1 0.313,0.771 0.469,0.969 0.156,0.198 10 3 1.323,0.771 1.479,0.969 0.156,0.198 10 5 1.323,1.271 1.479,1.469 0.156,0.198 10 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter No. 2 relay.