RM3090E
_V1
General
_009232
SPECIFICATIONS
_0050482
3ZR-FAE STARTING
F
SPECIFICATIONS 3ZR-FAE STARTING SERVICE DATA
STARTER ASSEMBLY
| Tester Connection
|
Condition
|
Specified Condition
|
| Battery positive (+) terminal - Terminal 30 - Terminal SL2
|
11.5 V
|
Below 130 A
|
STARTER ARMATURE ASSEMBLY
| Tester Connection
|
Condition
|
Specified Condition
|
| Segment - Segment
|
Always
|
Below 1 Ω
|
| Segment - Starter armature core
|
10 kΩ or higher
|
| Commutator for runout
|
Maximum Runout
|
0.05 mm (0.00197 in.)
|
| Commutator diameter
|
Standard Diameter
|
29 mm (1.1417 in.)
|
| Minimum Diameter
|
28 mm (1.1024 in.)
|
| Undercut depth
|
Standard Undercut Depth
|
0.7 mm (convex part) (0.0276 in.)
|
| Minimum Undercut Depth
|
0.4 mm (convex part) (0.0157 in.)
|
STARTER BRUSH HOLDER ASSEMBLY
| Brush length
|
Standard Length
|
14.4 mm (0.567 in.)
|
| Minimum Length
|
9 mm (convex part) (0.354 in.)
|
| Tester Connection
|
Condition
|
Specified Condition
|
A - B
A - C
B - D
C - D
|
Always
|
10 kΩ or higher
|
A - D
B - C
|
Below 1 Ω
|
| Brush spring load
|
Standard Spring Load
|
22 to 27 N (2 to 3 kgf, 4.9 to 6.1 lbf)
|
| Minimum Spring Load
|
14 N (1 kgf, 3.1 lbf)
|
REPAIR SERVICE STARTER KIT
| Tester Connection
|
Condition
|
Specified Condition
|
| Terminal SL1 - Magnet switch body
|
Always
|
Below 1 Ω
|
| Terminal SL2 - Magnet switch body
|
Below 2 Ω
|
ENGINE SWITCH
| Tester Connection
|
Switch Condition
|
Specified Condition
|
| 5 (SS1) - 6 (AGND)
|
Not pushed
|
10 kΩ or higher
|
| 1 (SS2) - 6 (AGND)
|
| 5 (SS1) - 6 (AGND)
|
Pushed
|
Below 1 Ω
|
| 1 (SS2) - 6 (AGND)
|
| Condition
|
Specified Condition
|
Battery positive (+) → Terminal 9 (SWIL)
Battery negative (-) → Terminal 6 (AGND)
|
Illuminates
|
IGNITION SWITCH
| Tester Connection
|
Switch Condition
|
Specified Condition
|
| All combinations of all terminals
|
LOCK
|
10 kΩ or higher
|
| 5 (AM1) - 7 (ACC)
|
ACC
|
Below 1 Ω
|
| 5 (AM1) - 7 (ACC)
|
ON
|
Below 1 Ω
|
| 5 (AM1) - 8 (IG1)
|
| 4 (AM2) - 3 (IG2)
|
| 6 (ST1) - 5 (AM1)
|
STRAT
|
Below 1 Ω
|
| 6 (ST1) - 8 (IG1)
|
| 2 (ST2) - 4 (AM2)
|
| 2 (ST2) - 3 (IG2)
|
STARTER RELAY (ST) (w/o Stop and Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|
STARTER NO. 1 RELAY (ST NO. 1) (w/ Stop and Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|
STARTER NO. 2 RELAY (ST NO. 2) (w/ Stop and Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|