Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM M

2WW ENGINE CONTROL  ECD SYSTEM  REGISTRATION  


CAUTION / NOTICE / HINT

HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.


·

After replacing any of the injector assemblies, perform the "Injector Compensation" function using the GTS. If any of the injector assemblies and the ECM are replaced at the same time, perform the same initialization/registrations as when replacing the ECM.


·

After replacing the air fuel ratio sensor, perform the "O2 Sensor Learning Value Reset" function using the GTS. If the air fuel ratio sensor and the ECM are replaced at the same time, perform the same initialization/registrations as when replacing the ECM.


·

After replacing the exhaust manifold converter subassembly(DPF catalytic converter), perform the "DPF History Information Reset" function using the GTS. If the exhaust manifold converter sub-assembly (DPF catalytic converter) and the ECM are replaced at the same time, perform the same initialization/registrations as when replacing the ECM.


·

After replacing the engine assembly, perform the "Injector Compensation" function using the GTS. If the engine assembly and the ECM are replaced at the same time, perform the same initialization/registrations as when replacing the ECM.


·

If the "Learning Values Save" or "Learning Values Write" function has failed, input manually the injector compensation codes using the "Injector Compensation" function by following the instructions shown on the GTS display.


·

The VIN is a 17-digit alphanumeric vehicle identification number. The GTS is required to register the VIN.


·

This registration section consists of 2 parts: Read VIN and Write VIN.



1.

Read VIN: This process allows the VIN stored in the ECM to be read in order to confirm that the 2 VINs, provided with the vehicle and stored in the vehicle ECM, are the same.

2.

Write VIN: This process allows the VIN to be input into the ECM. If the ECM is replaced, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.


PROCEDURE

Hide 1. LEARNING VALUES SAVE

HINT:

Save the compensation codes and learning values stored in the ECM to the GTS all at once in order to transfer the information from the old ECM to the new ECM.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Save
50005 371 2366

d.
A322134

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A322140

If "Learning Values Save" has failed, check the conditions and then perform it once again.



e.
A322135

If the overwrite confirmation screen is displayed, press "Overwrite".


f.
A322139

When the operation is finished, confirm the date and time of the save operation, and press "Exit".


Hide 2. LEARNING VALUES WRITE

HINT:
·

Write the compensation codes and learning values, which were stored in the GTS with "Learning Values Save", to the ECM all at once in order to transfer the information from the old ECM to the new ECM.

·

This function is used to write the compensation codes and learning values saved in the GTS.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Write
50005 371 4367

d.
A322132

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:

If "The saved data does not exist." or "The saved data is not for this vehicle." is displayed, perform "Learning Values Save" once again.


A322133


e.
A321481

Confirm the date and time of the save operation, and then press "Yes".

HINT:
A322136

If "Learning Values Write" has failed, check the conditions and then perform it once again.



f.
A322137

Press "Next" again to proceed.


g.
A322138

When the operation is finished, confirm the date and time of the save operation, and press "Exit".


Hide 3. LEARNING VALUES CONFIRMATION

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.

Powertrain > Engine and ECT > Utility
Tester Display
Learning Values Confirmation
50005 371 4403

Hide 4. INJECTOR COMPENSATION

NOTICE:

Injector compensation codes are 7-digit, alphanumeric values printed on the head of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


A312349C02
0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.229,2.354 1.542,2.552 0.313,0.198 10 false *b
*a Example
*b Injector Compensation Code


A321470E01
0.104,0.083 1.979,0.313 1.875,0.229 10 false Injector Compensation Code: 3.479,0.292 3.844,0.5 0.365,0.208 10 false Start 3.729,0.646 4.208,0.844 0.479,0.198 10 false Next 2.865,1.031 4.49,1.229 1.625,0.198 10 false Select Cylinder Number 3.719,1.458 4.104,1.656 0.385,0.198 10 false Next 1.365,2.031 4.104,2.271 2.74,0.24 10 false Input Injector Compensation Code Manually 1.375,2.333 3.76,2.563 2.385,0.229 10 false Confirm Injector Compensation Code 4.396,1.948 4.854,2.156 0.458,0.208 10 false Input 4.208,2.417 5.24,2.625 1.031,0.208 10 false OK or Cancel 5.188,2.083 5.896,2.292 0.708,0.208 10 false Keyboard 3.281,2.719 3.688,2.938 0.406,0.219 10 false Next 1.677,3.083 3.052,3.323 1.375,0.24 10 false Invalid Number Input 4.323,3.094 5.542,3.354 1.219,0.26 10 false Compensation Fail 0.906,3.354 1.563,3.604 0.656,0.25 10 false Try Again 5.656,3.354 6.313,3.604 0.656,0.25 10 false Try Again 1.75,4.313 2.156,4.531 0.406,0.219 10 false Next 2.427,4.146 4.927,4.406 2.5,0.26 10 false Register Compensation Code Complete 3.698,4.552 4.031,4.76 0.333,0.208 10 false Exit 3.521,5.26 3.938,5.469 0.417,0.208 10 false End

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

HINT:

Confirm that the ignition switch is ON and the engine is stopped.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 371 4360

d.
A321480

When the first screen is displayed, check the vehicle condition and push "Next".


e.
A321471

Select the number of the cylinder corresponding to the injector compensation code that you want to input, and press "Next".


f.
A321472

Register the compensation code.

i.

Manually input the cylinder compensation code using the keyboard. The code is a 7-digit, alphanumeric value printed on the injector head.

HINT:

The compensation code for each selected cylinder must be input into the GTS correctly.



ii.

Confirm that the compensation code for the selected cylinder is correct, and then Press "Next".

HINT:
·
A321479

If an input error occurs, input the compensation code once again.

·
A321475

If registering the compensation code has failed, check the conditions and perform the registration once again.





g.
A321473

Press "Back" to return to the screen for selecting the cylinder when registering the compensation code of another cylinder. Then press "Next".


h.
A321476

Press "Next".


i.
A321478

When the operation is finished, confirm the date and time of the save operation, and press "Exit".


Hide 5.READ VIN

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Read.

Powertrain > Engine and ECT > Utility
Tester Display
VIN
50005 371 2363

Hide 6.WRITE VIN

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Write.

Powertrain > Engine and ECT > Utility
Tester Display
VIN
50005 371 2363