Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM D

2WW ENGINE CONTROL  ECD SYSTEM  INITIALIZATION  


Supply Pump Learning Value Reset


HINT:

When a fuel supply pump assembly is replaced, the fuel supply pump learning value stored in the ECM must be reset.

This function is used to reset the fuel supply pump learning value stored in the ECM upon replacing the fuel supply pump assembly.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Supply Pump Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Supply Pump Learning Value Reset
50005 371 4369

e.
A322125

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A322131

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



f.
A322126

When the screen indicating reset completion is displayed, push "Exit".



EGR Learning Value Reset


HINT:

When an EGR valve assembly is replaced, the EGR learning value stored in the ECM must be reset.

This function is used to reset the EGR learning value stored in the ECM upon replacing the EGR valve assembly.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / EGR Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
EGR Learning Value Reset
50005 371 4370

e.
A322117

When the first screen is displayed, check the vehicle condition and push "Next".

NOTICE:

DTC P042F is output when performing EGR learning value reset. Therefore, after starting the engine, clear the DTCs.


HINT:
A322128

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



f.
A322118

When the screen indicating reset completion is displayed, push "Exit".


g.

Start the engine 3 times and keep the engine speed above 3000 rpm for 3 seconds each time.



Air Flow Meter Learning Value Reset


HINT:

When a mass air flow meter is replaced, the air flow meter learning value and deterioration compensation stored in the ECM must be reset.

This function is used to reset the air flow meter sub-assembly learning value and deterioration compensation stored in the ECM upon replacing the mass air flow meter sub-assembly.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Flow Meter Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Air Flow Meter Learning Value Reset
50005 371 4371

e.
A322114

A322127

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:

If an error occurs during learning value reset, check the vehicle condition, and then perform compensation reset again.



f.
A322115

Press "Next".


g.
A322116

When the screen indicating reset completion is displayed, push "Exit".



DPF History Information Reset


HINT:
·

This value is the ash accumulation volume in the exhaust manifold converter sub-assembly (DPF catalytic converter) calculated by the ECM. If the ash accumulation volume in the exhaust manifold converter sub-assembly (DPF catalytic converter) increases, the difference in pressure in front of and behind the exhaust manifold converter sub-assembly (DPF catalytic converter) will increase. The difference in pressure in front of and behind the exhaust manifold converter sub-assembly (DPF catalytic converter) is offset depending on the volume of accumulated ash.

·

When an exhaust manifold converter sub-assembly (DPF catalytic converter) is replaced, the DPF deterioration record stored in the ECM must be cleared.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / DPF History Information Reset.

Powertrain > Engine and ECT > Utility
Tester Display
DPF History Information Reset
50005 371 4368

d.
A322120

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A322129

If an error occurs during history information reset, check the vehicle condition, and then perform history information reset again.



e.
A322122

Press "Next".


f.
A322121

When the screen indicating reset completion is displayed, push "Exit".



O2 Sensor Learning Value Reset


HINT:

When an air fuel ratio sensor is replaced, the air fuel ratio sensor learning value stored in the ECM must be reset.

This function is used to reset the air fuel ratio sensor learning value stored in the ECM upon replacing the air fuel ratio sensor.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / O2 Sensor Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
O2 Sensor Learning Value Reset
50005 371 4373

d.
A322123

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A322130

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A322124

When the screen indicating reset completion is displayed, push "Exit".



Differential Pressure Learning Value Reset


HINT:

When a differential pressure sensor is replaced, the differential pressure sensor learning value stored in the ECM must be reset.

This function is used to reset the differential pressure sensor learning value stored in the ECM upon replacing the differential pressure sensor.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Differential Pressure Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Differential Pressure Learning Value Reset
50005 371 2389

d.
A342494

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A342495

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A342496

When the screen indicating reset completion is displayed, push "Exit".



Swirl Valve Learning Value Reset


HINT:

When a swirl control valve is replaced, the swirl control valve learning value stored in the ECM must be reset.

This function is used to reset the swirl control valve learning value stored in the ECM upon replacing the swirl control valve.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Swirl Valve Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Swirl Valve Learning Value Reset
50005 371 2387

d.
A342497

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A342498

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A342499

When the screen indicating reset completion is displayed, push "Exit".



Upstream Turbine Pressure Learning Value Reset


HINT:

When a turbo pressure sensor is replaced, the turbo pressure sensor learning value stored in the ECM must be reset.

This function is used to reset the turbo pressure sensor learning value stored in the ECM upon replacing the turbo pressure sensor.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Upstream Turbine Pressure Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Upstream Turbine Pressure Learning Value Reset
50005 371 2390

d.
A342500

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A342501

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A342502

When the screen indicating reset completion is displayed, push "Exit".



NOx Storage Catalyst Learning Value Reset


HINT:

When an exhaust manifold converter sub-assembly (catalytic converter) is replaced, the NOx storage catalyst learning value stored in the ECM must be reset.

This function is used to reset the NOx storage catalyst learning value stored in the ECM upon replacing the exhaust manifold converter sub-assembly (catalytic converter).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / NOx Storage Catalyst Learning Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
NOx Storage Catalyst Learning Value Reset
50005 371 4388

d.
A342503

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A342504

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A342505

When the screen indicating reset completion is displayed, push "Exit".



Fuel PCV Compensation Value Reset


HINT:

When a pressure discharge valve is replaced, the fuel PCV compensation value stored in the ECM must be reset. This function is used to reset the fuel PCV compensation value stored in the ECM upon replacing the pressure discharge valve.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel PCV Compensation Value Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Fuel PCV Compensation Value Reset
50005 371 4427

d.
A351148

When the first screen is displayed, check the vehicle condition and push "Next".

HINT:
A351149

If an error occurs during learning value reset, check the vehicle condition, and then perform learning value reset again.



e.
A351150

When the screen indicating reset completion is displayed, push "Exit".