Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049621 STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY G

STOP AND START  STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT STOP AND START SYSTEM CANCEL SWITCH (for 2WW)

a.
A273347C01
2.479,1.99 2.302,1.99 2.302,1.99 1.99,1.448 true 0.979,1.969 1.198,1.969 1.198,1.969 1.479,1.438 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.583,1.906 3.042,2.104 0.458,0.198 10 false ECU 0.76,1.885 1.083,2.083 0.323,0.198 10 false E
*a Component without harness connected
(Stop and Start System Cancel Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ECU) - 4 (E) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the stop and start system cancel switch.


b.
A273347C02
0.74,1.958 0.958,1.958 0.958,1.958 1.24,1.448 true 2.688,1.948 2.448,1.948 2.448,1.948 2.26,1.448 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 2.823,1.865 3.25,2.073 0.427,0.208 10 false ILL+ 0.375,1.885 0.802,2.094 0.427,0.208 10 false ILL-
*a Component without harness connected
(Stop and Start System Cancel Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the stop and start system cancel switch.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ILL+)
Battery negative (-) → 5 (ILL-)
Illuminates


If the result is not as specified, replace the stop and start system cancel switch.


Hide 84970 2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (for 3ZR-FAE)

a.

for Manual Transaxle:

i.
A273347C03
2.479,1.99 2.302,1.99 2.302,1.99 1.99,1.448 true 0.979,1.969 1.198,1.969 1.198,1.969 1.479,1.438 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.552,1.917 3.01,2.115 0.458,0.198 10 false ECU 0.51,1.896 1.125,2.094 0.615,0.198 10 false MSW2
*a Component without harness connected
(Stop and Start System Cancel Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ECU) - 4 (MSW2) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the stop and start system cancel switch.


ii.
A273347C04
0.74,1.958 0.958,1.958 0.958,1.958 1.24,1.448 true 2.688,1.948 2.448,1.948 2.448,1.948 2.26,1.448 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 2.823,1.865 3.385,2.115 0.563,0.25 10 false MSW+ 0.302,1.875 0.948,2.073 0.646,0.198 10 false MSW-
*a Component without harness connected
(Stop and Start System Cancel Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the stop and start system cancel switch.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (MSW+)
Battery negative (-) → 5 (MSW-)
Illuminates


If the result is not as specified, replace the stop and start system cancel switch.



b.

for CVT:

i.
A352983C01
1.031,1.885 1.156,1.885 1.156,1.885 1.406,1.313 true 1.604,1.313 1.896,1.896 1.896,1.896 2.021,1.896 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.552,1.802 1.167,2 0.615,0.198 10 false MSW2 2.094,1.813 2.542,2.01 0.448,0.198 10 false ECU
*a Component without harness connected
(Stop and Start System Cancel Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (ECU) - 6 (MSW2) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the stop and start system cancel switch.


ii.
A352983C02
0.792,1.823 0.917,1.823 0.917,1.823 1.177,1.313 true 2.688,1.854 2.552,1.854 2.552,1.854 2.229,1.323 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.344,1.74 0.958,1.938 0.615,0.198 10 false MSW- 2.771,1.792 3.292,2.021 0.521,0.229 10 false MSW+
*a Component without harness connected
(Stop and Start System Cancel Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the stop and start system cancel switch.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (MSW+)
Battery negative (-) → 7 (MSW-)
Illuminates


If the result is not as specified, replace the stop and start system cancel switch.