Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR(for 150 A Type) › from 2015.10
RM3090E _57 Power Source / Network _008403 2AR-FE BATTERY / CHARGING _0208709 GENERATOR(for 150 A Type) A

2AR-FE BATTERY / CHARGING  GENERATOR(for 150 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A194719

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.
A197237C07
1.75,1 1.667,0.167 1.667,0.167 3,0.667 true 1.167,1.25 1.833,2 1.833,2 1.917,2 true 1.583,0.167 1.667,0.167 false 2.198,1.427 2.198,0.76 true 2.125,1.427 2.438,1.583 0.313,0.156 10 false *a 1.021,0.083 1.667,0.25 0.646,0.167 10 false SST (A) 2.021,1.885 2.667,2.052 0.646,0.167 10 false SST (B)
*a Gnerator Rotor Shaft


Mount the generator assembly in a vise between aluminum plates.


b.

Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


c.
A197239C10
2.177,0.823 2.417,0.417 2.417,0.417 2.583,0.417 false 1.927,0.573 2.167,0.167 2.167,0.167 2.333,0.167 false 1.823,1.854 2.135,2.01 0.313,0.156 10 false *a 2.667,0.333 3.323,0.531 0.656,0.198 10 false SST (A) 2.406,0.083 3.063,0.281 0.656,0.198 10 false SST (B)
*a Hold
V100135

Turn


Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator pulley with clutch.


d.

Remove the generator pulley with clutch.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A370704

Place the generator on the generator pulley with clutch.


b.
A192779

Remove the 3 bolts and generator rear end cover.


Hide 27387 4.REMOVE TERMINAL INSULATOR

a.
A192780

Remove the terminal insulator.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A192783E01
0.533,0.31 0.837,0.484 0.303,0.173 10 SST 1.583,0.78 1.028,0.404 1.028,0.404 0.902,0.404 false

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A370698

Remove the generator washer.


b.
A370699

Remove the generator rotor assembly from the generator drive end frame assembly.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A192785

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If the result is not as specified, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and bearing retainer.


b.
A192788N04
1.583,1.365 0.979,0.5 0.979,0.5 1.625,0.844 true 0.656,0.396 1.115,0.594 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)