Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR(for 150 A Type) › from 2015.10
RM3090E _57 Power Source / Network _008403 2AR-FE BATTERY / CHARGING _0208709 GENERATOR(for 150 A Type) A

2AR-FE BATTERY / CHARGING  GENERATOR(for 150 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

A192789E01
0.193,0.71 0.506,0.898 0.313,0.188 10 SST 1.629,0.794 0.558,0.794 false 1.499,1.142 0.944,1.142 0.944,1.142 0.944,0.792 false

a.

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.

Install the bearing retainer with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A192790

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A192792C07
0.906,0.24 1.208,0.24 1.208,0.24 1.625,0.698 true 0.719,0.156 1.031,0.313 0.313,0.156 10 false *a
*a 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


b.

Install the generator coil assembly with the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A158992C22
0.99,0.719 1.156,0.313 1.156,0.313 1.365,0.313 true 1.406,0.229 1.719,0.385 0.313,0.156 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly.


b.
A192793C08
1.594,0.948 2.125,0.26 2.125,0.26 2.375,0.26 true 2.438,0.177 2.75,0.333 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull the pin out of the generator brush holder assembly.


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.

Install the terminal insulator to the generator coil assembly.


Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley with clutch by hand.


b.

Mount the generator assembly in a vise between aluminum plates.


c.
A197238C07
1.417,2 1.583,2 1.583,2 2.25,1.25 true 0.417,0.667 1.417,0.167 1.417,0.167 1.583,1 true 1.417,0.167 1.5,0.167 false 1.167,1.5 1.167,0.75 true 0.875,1.896 1.594,2.083 0.719,0.188 10 false SST (B) 1.563,0.073 2.281,0.26 0.719,0.188 10 false SST (A) 1.104,1.5 1.417,1.656 0.313,0.156 10 false *a
*a Gnerator Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


d.
A370705C01
0.604,0.677 0.729,0.677 0.729,0.677 1.021,1.042 true 0.802,0.354 0.927,0.354 0.927,0.354 1.354,0.875 true 1.219,2.635 1.531,2.792 0.313,0.156 10 false *a 1.979,2.552 2.292,2.708 0.313,0.156 10 false *b 0.063,0.604 1.135,0.802 1.073,0.198 10 false SST (A) 0.271,0.271 1.344,0.469 1.073,0.198 10 false SST (B)
*a Hold
*b Fulcrum Length
V100135

Turn


Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 64 N*m (653 kgf*cm, 47 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure SST and the wrench are connected in a straight line.



NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



e.

Remove SST from the generator.


f.

Check that the generator pulley with clutch rotates smoothly.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.
A370706

Install a new generator pulley cap to the generator pulley with clutch.