STOP AND START CONTROL
The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.
When all of the conditions in the following table have been met, the engine is stopped by stop and start system control.
| Item | Condition
(All of the following conditions are met) |
|
|---|---|---|
| Idle Stop | Ignition Switch | 5 seconds or more have passed with the ignition switch ON |
| Engine Coolant Temperature | 40 to 105°C (104 to 221°F) | |
| Ambient Temperature | -5°C (23°F) or higher | |
| Driver Door | 3 seconds have elapsed after driver door closed | |
| Driver Seat Belt | 3 seconds have elapsed after driver seat belt fastened | |
| Vehicle Stability Control System | Normal | |
| Brake Booster Vacuum | Sufficient (42.5 kPa (319 mmHg, 12.6 in.Hg) or higher at horizontal road) | |
| Shift Position | Shift lever in neutral | |
| Stop and Start System Cancel Switch | Off (system control is not prohibited) | |
| Vehicle Speed | 0 km/h (0 mph) (After the engine warms up) | |
| Engine Speed | Below 1250 rpm | |
| Engine Hood | 3 seconds have elapsed after hood closed | |
| Battery Voltage | When using specified battery:
Higher than 6.6 V when starter begins operation and higher than 7.27 V when cranking |
|
| Battery Temperature*1 | -10 to 70°C (14 to 158°F) | |
| Battery Integrated Current*2 | One of the following condition is met:
·
Higher than -5299 A-sec: "Status of Battery Charge Control"*3 is Charge Control Coordination Mode or Low Temperature Mode ·
Higher than 0 A-sec: "Status of Battery Charge Control"*3 is Stop and Start Standalone Mode, Stop and Start Restriction Mode or Temperature High/Low Mode |
|
| Air Conditioning | Other than when stop and start control is prohibited | |
| Heater | Once of the following conditions is met:
·
Blower switch is off. ·
Blower switch is on when the ambient temperature is higher than 10°C (50°F), the engine coolant temperature is higher than 55°C (131°F) or the room temperature is higher than the set temperature minus 5°C (23°F) (only when stop and start system priority control is set to "Normal" mode) (w/ Automatic Air Conditioning System) ·
Blower switch on, air conditioning switch off and a certain amount of time has elapsed after engine restarted by stop and start control |
|
| Steering Operation | When the steerage angle of the steering wheel is less than 25 degrees and 45 deg/s or less | |
*1: When the battery temperature is -15°C (5°F) or less, or 75°C (167°F) or higher, the stop and start control is prohibited. When the battery temperature returns to -10°C (14°F) or higher, or 70°C (158°F) or less, stop and start control is permitted.
*2: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DATA LIST / ACTIVE TEST
*3: Please refer to the Data List item "Status of Battery Charge Control" for information about the status of the battery charge control.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DATA LIST / ACTIVE TEST
When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.
| Item | Condition
(All of the following conditions are met) |
|
|---|---|---|
| Engine Restart | Brake Booster Vacuum | Brake booster vacuum insufficient (Brake booster vacuum changes in accordance with brake fluid pressure (brake pedal effort)) |
| Engine Hood Courtesy Switch (Hood Lock Assembly) | Engine hood courtesy switch (hood lock assembly) malfunctioning | |
| ECD System | Malfunction in ECD system is detected | |
| Power Steering System | Malfunction in power steering system is detected | |
| Vehicle Stability Control System | Malfunction in vehicle stability control system is detected | |
| Air Conditioning | The timer in the air conditioning amplifier assembly runs out | |
| Heater | The timer in the air conditioning amplifier assembly runs out. | |
| Air Conditioning/Heater | Both of the following conditions are met:
·
Blower switch: ON ·
Evaporator temperature exceeds threshold value (threshold value varies with temperature, humidity and amount of solar radiation) Any of the following conditions are met:
·
A/C switch, blower switch: ON ·
Defogger switch: ON ·
Blower switch turned off during auto control or blower mode changed to manual (w/ Automatic Air Conditioning System) ·
Changes from stop and start system priority control to normal system control |
|
| Battery | Battery performance or voltage drops (11.4 V or less) | |
| Battery Integrated Current*1 | The accumulated value of discharge current during engine stop is too large (over 6912 A-sec). | |
| Vehicle Speed | Vehicle speed signal is input | |
| Driver Door | Open | |
| Driver Seat Belt | Driver seat belt is unfastened | |
| Stop and Start System Cancel Switch | Stop and start system cancel switch (combination switch assembly) is turned from off to on | |
| Clutch Pedal | When the clutch pedal is depressed | |
| Steering Wheel | Steering wheel turned 25 degrees or more and 45 deg/s or higher | |
| Heater and Accessary Assembly*2 | The heater switch assembly is turned on | |
*1: Read the Data List item "Integrated Current" or "Oper Permission (IntegratedCurrent)" when checking the integrated current value.
*2: w/ Combustion Type Power Heater System
SYSTEM PROHIBITION CONTROL
The engine stop and start ECU prohibits stop and start control by the stop and start system according to the table below. The prohibition conditions are specified for each system.
| Item | Prohibition Condition | Vehicle State | Restoration Condition | Prohibition Condition Check Timing |
|---|---|---|---|---|
| Engine | Engine coolant temperature less than 40°C (104°F) | Engine has not warmed up | Engine coolant temperature 40 between 105°C (104 to 221°F) | Always |
| Idle speed learning has not completed | Stop and start control prohibited until idle speed learning completes | Idle speed learning has completed | Always | |
| Engine catalytic rapid warm-up | Engine catalytic rapid warm-up is being performed | Engine catalytic rapid warm-up is completed | Each time engine is started or vehicle is stopped | |
| Brake | Brake booster vacuum decreases | Brake booster vacuum decreases due to pumping the brakes, etc. | Normal brake booster vacuum is reached | Every time the vehicle stops |
| Air Conditioning | Heater:
When blower switch is on and ambient temperature 10°C (50°F) or less, any of the following conditions are met:
·
Engine coolant temperature 55°C (131°F) or less ·
Cabin temperature equal to or lower than set temperature minus 5°C (23°F) (only when stop and start system priority control is set to "Normal" mode) (w/ Automatic Air Conditioning System) |
Heater performance decreases | ·
Actual temperature higher than target temperature ·
Blower switch is off |
While the heater is on |
| Heater switch is on (for Combustion Type Power Heater System) | - | Heater switch is off (for Combustion Type Power Heater System) | While the heater is on | |
| Cooling function:
When blower switch and A/C switch is on and ambient temperature 23°C (73.4°F) or higher, any of the following conditions are met:
·
Evaporator temperature 9°C (48.2°F) or higher ·
Cabin temperature higher than set temperature by 3°C (37.4°F) or more, or blower level 16 or higher (only when stop and start system priority control is set to "Normal" mode) (w/ Automatic Air Conditioning System) |
Cooling performance decreases | Any of the following conditions have been met
·
Actual temperature higher than target temperature ·
Blower switch is off ·
Air conditioning switch is off |
While the air conditioning system (cooling function) is on | |
| Defogger:
·
Defogger switch and blower switch on (w/ Automatic Air Conditioning System) |
Fogging of windows | Blower switch is off or defogger switch off | While the air conditioning system (cooling function for defogger) is on | |
| Temporary start and start control:
Both of the following conditions are met:
·
Blower switch on ·
Evaporator temperature exceeds threshold (threshold varies with temperature, humidity and amount of solar radiation) |
Blower switch on | Blower switch off and evaporator temperature within specified range | Always | |
| Driver Door | Driver door is opened before engine stop by engine stop and start control | Driver door courtesy switch ON signal is input | 3 seconds have elapsed since driver door was closed | Always |
| Engine Hood | Engine hood is opened before engine stop by stop and start control | Engine hood courtesy switch (hood lock assembly) OFF signal is input | 3 seconds have passed since engine hood was closed | Always |
| Seat Belt | Driver seat belt is not fastened before engine stop by engine stop and start control | Driver seat belt buckle switch OFF signal is input | 3 seconds have passed since driver seat belt was fastened | Always |
| Steering Wheel | Steering wheel turned at a speed of 45 deg/s or more | Steering wheel operation signal input | Steering wheel being held | Always |
| Ambient Temperature | Ambient temperature below -5°C (23°F) | - | Ambient temperature -5°C (23°F) or higher | Always |
| Power Source | When using specified battery:
Higher than 6.6 V when starter begins operation and higher than 7.27 V when cranking |
Battery charge is insufficient or battery has deteriorated | Battery is charged or replaced | Every time the engine is started |
| Battery temperature below -15°C (5°F) or 75°C (167°F) or higher | Depends on ambient temperature | An appropriate battery temperature is reached (between -10 and 70°C (14 to 158°F)) | Always | |
Battery integrated current *1 value meets one of the following conditions:
·
-6451 A-sec or less: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Low Temperature Mode ·
-1152 A-sec or less: "Status of Battery Charge Control"*2 is Stop and Start Standalone Mode, Stop and Start Restriction Mode or Temperature High/Low Mode |
·
Heavy electrical load ·
High stop and start rate (Time that engine stopped by stop and start control is long) |
Battery integrated current *1 value meets one of the following conditions:
·
-5299 A-sec or higher: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Low Temperature Mode ·
0 A-sec or higher: "Status of Battery Charge Control"*2 is Stop and Start Standalone Mode, Stop and Start Restriction Mode or Temperature High/Low Mode |
Always | |
| During refresh charge | ·
Cable reconnected to negative (-) battery terminal ·
Refresh charge is performed for 30 minutes or longer for every 20 hours of driving |
30 minutes to 1 hour has elapsed | Always | |
| Engine is started with the engine hood open (for jump starting) | - | After ignition switch is turned off, ignition switch is turned to ON with hood closed | Every time the engine is started | |
| Clutch Pedal | Clutch pedal is depressed | - | Clutch pedal is released | Every time the vehicle is stopped |
| Shift Range | Shift lever not in neutral | - | Shift lever in neutral | Every time the vehicle is stopped |
| Idling Stop Rate | Idling stop rate for one trip is over 50% or total idling stop rate is over 40% | Vehicle is stopped for long time | Idling stop rate has decreased due to vehicle being driven and engine idling | Always |
*1: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value.
*: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DATA LIST / ACTIVE TEST
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.
WARNING CONTROL
If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.
| Operation | Warning Control |
|---|---|
| The driver door is opened with the shift lever is in neutral | The engine starts |
| The driver door is opened with the shift lever in other than neutral | The buzzer sounds and stop and start indicator light blinks (engine will not start) |
| The driver seat belt is unfastened with the shift lever is in neutral | The engine starts |
| The engine hood opened | The engine changes to "stalled" (once the ignition switch is turned off, and then turned from off to ON again, the engine returns to normal) |
| The shift lever is operated without depressing the clutch pedal | The buzzer sounds and stop and start indicator light blinks (engine will not start) |
WARNING INDICATOR AND BUZZER OPERATION
| *a | Stop and Start Indicator Light |
| *b | Stop and Start Cancel Indicator Light |
The driver is informed of the system control status and warnings by the stop and start indicator light, stop and start cancel indicator light and the buzzer.
| Item | Condition | Stop and start indicator light | Stop and start cancel indicator light | Buzzer |
|---|---|---|---|---|
| For 3 seconds after the ignition switch to ON | Normal operation | Comes on | Comes on | Does not sound |
| During stop and start control operation (engine is stopped) | Normal operation | Comes on | Does not come on | Does not sound |
| The shift lever is operated without depressing the clutch pedal | The blinking interval is 0.15 seconds. | Does not come on | Sounds | |
| After engine started by stop and start control | Driver door opened within 5 seconds of engine start | The blinking interval 0.15 seconds | Does not come on | Sounds |
| Control is prohibited by the stop and start system cancel switch (combination switch assembly) | Normal operation | Does not come on | Comes on | Does not sound |
| Diagnostic trouble code | Any DTCs are stored | Does not come on | The blinking interval is 0.5 seconds. | Does not sound |
| Starter life | The number of times the starter has been operated exceeds its limit | Does not come on | The blinking interval is 0.5 seconds. | Does not sound |
STOP AND START SYSTEM OPERATION CONDITION DISPLAY FUNCTION
The stop and start system operation condition is displayed on the multi-information display.
*1: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.
| Stop and Start System Condition | Multi-information Display Message*2 | Vehicle Condition | |
|---|---|---|---|
| When the engine cannot be stopped by the stop and start system |
*1 |
"For Climate Control" | ·
The air conditioning system is being used when the ambient temperature is high or low. ·
Windshield defogger is pressed. |
| "Battery Charging" | ·
The battery charge amount may be low. ·
A refresh charge may be occurring. ·
The engine may have been started with the hood opened. ·
The battery may be cold. ·
The battery may be extremely hot. |
||
| "For Brake System" | ·
The brake booster load decreased. ·
The vehicle is operated at a high elevation. |
||
| "Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. | ||
| When the engine automatically restarts while stopped by the stop and start system |
*1 |
"Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. |
| "Steering Wheel Turned" | The steering wheel is turned. | ||
| "For Brake System" | The brake pedal is strongly depressed further or pumped. | ||
| "For Climate Control" | ·
The air conditioning system is turned on or the air conditioning is being used. ·
Windshield defogger is turned on. |
||
| "Battery Charging" | The battery charge amount may be low. | ||
| The system may be malfunctioning | - | "Stop & Start System Malfunction"
"Visit Your Dealer" |
- |
*2: Examples of messages displayed during different situations are listed below in order of priority (some messages may not be displayed depending on the vehicle).
Engine cannot be stopped by stop and start system
"Battery Charging", "For Brake System", "For Climate Control", "Driver Seat Belt Unbuckled"
Engine automatically restarted while engine stopped by stop and start system
"Driver Seat Belt Unbuckled", "Steering Wheel Turned", "For Brake System", "For Climate Control", "Battery Charging"
STOP AND START SYSTEM OPERATION
Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunction in the stop and start system.
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| IGSW circuit | Open | P2531 | ·
IG Switch ·
IG SW Abnoml |
Stop and start control prohibited | Wire harness or connector |
| +B circuit | Open | - | Data List cannot be checked because power is not supplied to the engine stop and start ECU | Stop and start control prohibited | Wire harness or connector |
| TMN (neutral position sensor (neutral position switch)) circuit | Open | P1780 | ·
Neutral Switch ·
N position Switch ·
N Position Voltage Status |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Neutral position sensor (neutral position switch) |
| Shorted | P1780 | ·
Neutral Switch ·
N position Switch ·
N Position Voltage Status |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
||
| CLL (clutch start switch assembly (for lower)) circuit | Stuck on | P1862 | ·
Clutch Lower SW ·
N/Clutch Lower SW Abnoml |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Clutch start switch assembly (for lower) ·
Clutch start switch assembly (for upper) |
| Stuck off | - | ·
Clutch Lower SW ·
Clutch Lower SW Stuck OFF ·
Clutch Lower SW Abnoml (OFF) |
Stop and start control prohibited | ||
| CLU (clutch start switch assembly (for upper)) circuit | Stuck on | P1862 | ·
Clutch Upper SW ·
Clutch Upper SW Stuck ON ·
N/Clutch Upper SW Abnoml (ON) |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
|
| Stuck off | - | ·
Clutch Upper SW ·
Clutch Upper SW Stuck OFF ·
N/Clutch Upper SW Abnoml (OFF) |
Stop and start control prohibited | ||
| BNT1 (engine hood courtesy switch (hood lock assembly)) circuit | Stuck on | - | Hood Courtesy Switch | The engine does not stall when the engine hood is opened with the shift lever in neutral while the engine is stopped by stop and start control | ·
Wire harness or connector ·
Engine hood courtesy switch (hood lock assembly) |
| Stuck off | - | Hood Courtesy Switch | Stop and start control prohibited despite the engine hood being closed | ||
| BRVC/PB/BRE2 (vacuum sensor) circuit | Open | P1540 | ·
Brk Boost Sen Abnoml 1 ·
Brk Boost Sen Abnoml 2 ·
Brk Boost Sen Abnoml 3 |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Vacuum sensor assembly ·
Brake booster assembly ·
Vacuum hose (brake booster hose) |
| Shorted | P1540 | ||||
| Remains at intermediate value | P1541 | ||||
| ECAN (stop and start system cancel switch (combination switch assembly)) circuit | Stuck on | - | Cancel Switch | Stop and start control prohibited | ·
Wire harness or connector ·
Stop and start system cancel switch (combination switch assembly) |
| Stuck off | - | Cancel Switch | Stop and start control cannot be canceled by pressing the stop and start system cancel switch (combination switch assembly) | ||
| STA circuit | Overcurrent | P0617 | ·
Starter Relay Overcurrent ·
Starter Circuit Abnoml ·
Starter Circuit Open |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
ST relay ·
Engine stop and start ECU |
| Stuck on | P1644 | ·
Wire harness or connector ·
ST relay ·
Engine stop and start ECU |
|||
| Stuck off | P1644 | ||||
| BBC (backup boost converter) circuit | Overcurrent | B22C0 | ·
State of BBC ·
BBC Abnoml ·
BBC Overcurrent ·
BBC Check Result |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery ·
ECUs and sensors connected to B41 and IG41 |
·
Open ·
Shorted ·
Internal circuit ·
Battery |
P323B | ·
State of BBC ·
BBC Duty ·
BBC Thermistor ·
BBC Abnoml ·
BBC Over Heat ·
BBC Power Low |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
|
| ECU inner circuit | Malfunction | P0607 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| Monitoring CPU circuit | Malfunction | P060A | State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| EEPROM | Malfunction | P062F | EEPROM | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| ECD system | MIL illuminated | DTCs for ECD system output | ·
Oper Permission (ECM 1) ·
Oper Permission (ECM 2) |
Stop and start control prohibited | ECD system |
| Abnormal NE signal | DTCs for ECD system output | ·
NE Sensor Circuit Open2 ·
Crank Pos Sen Abnoml 3 |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
ECD system (crank position sensor circuit) ·
Wire harness or connector |
|
| Crankshaft reverse rotation detection | DTCs for ECD system output | - | ·
Stop and start control prohibited ·
MIL illuminated |
ECD system (crank position sensor circuit) | |
| Charging system | Battery current sensor malfunction | DTCs for charging system output | ·
Battery Fluid Temperature ·
Integrated Current |
Stop and start control prohibited | Charging system |
| Brake control system | Vehicle stability control running | - | ABS Running | Stop and start control prohibited | - |
| Malfunction in wheel speed sensor | Brake control system DTCs output | ·
Vehicle Spd1 (ABS/VSC) ·
Wheel Speed Malfunction |
Stop and start control prohibited | ·
Wire harness or connector ·
Skid control ECU (brake actuator assembly) ·
Vehicle speed sensor |
|
| Power steering system | Malfunction in power steering system | EPS assist current value invalid | ·
EPS Load ·
Comm Err with EPS |
Stop and start control prohibited | ·
Power steering ECU assembly ·
Torque sensor |
| Seat belt warning system | Malfunction in seat belt warning system | - | Oper Permission (Driver Side Buckle SW) | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front seat inner belt assembly (Driver side) ·
Wire harness or connector |
| Driver door courtesy light switch circuit | Malfunction in driver door courtesy light switch circuit | - | D Courtesy Switch Signal | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front door courtesy light switch assembly (Driver side) ·
Driver door courtesy light switch circuit |
| Air conditioning system | Malfunction in ambient temperature sensor | Air conditioning system DTCs output | Ambient Temp Sensor | Stop and start control prohibited | Ambient temp sensor circuit |
| Brake vacuum | Brake booster vacuum drops | - | ·
Brake Boost Pressure ·
Brake Negative Pressure ·
Brk Boost Sen Abnoml 1 ·
Brk Boost Sen Abnoml 2 ·
Brk Boost Sen Abnoml 3 |
Stop and start control prohibited | ·
Brake booster assembly vacuum ·
Brake booster assembly ·
Vacuum sensor assembly ·
Vacuum hose (brake booster hose) |
| Power source | Backup boost converter malfunction | P323B | ·
State of BBC ·
BBC Duty ·
BBC Thermistor ·
BBC Abnoml ·
BBC Over Heat ·
BBC Power Low |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
| Charging system malfunction | - | Alternator Status | Stop and start control prohibited | Charging system | |
| Low voltage | P0562 | Battery Abnoml | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Battery ·
Relay |
|
| Number of starter operations | Exceeds the specified limit | P1545 | Starter Count Abnoml | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Starter assembly replacement is required. ·
ST relay replacement is required. ·
Fuse replacement is required. |
| Starter signal malfunction | Signal does not match with the starter switch | P1545 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Engine stop and start ECU |
| Jump start | Engine started with the engine hood open | - | Eng Start Reg (Engine Hood Open) | Stop and start control prohibited
(permitted when the ignition switch is turned off) |
·
Check for a history of roadside service or jump start due to dead battery ·
Engine hood courtesy switch (hood lock assembly) |
| CAN communication | Communication interrupted | U0100
U0121 U0126 U0131 U0140 U0151 U0155* U0164 |
- | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks* |
·
Applicable wire harness or connector ·
Applicable ECU |
*: The stop and start cancel indicator light does not blink when a communication error with the combination meter assembly occurs.