Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) D

STOP AND START  STOP AND START SYSTEM(for 2WW)  FREEZE FRAME DATA  


DESCRIPTION


The engine stop and start ECU records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

NOTICE:
·

Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.

·

Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data using the GTS.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check for DTCs and read the freeze frame data.



LIST OF FREEZE FRAME DATA


Powertrain > Stop and Start
Tester Display Measurement Item
Coolant Temp Engine coolant temperature
Engine Spd (ECM) Engine speed signal from ECM through CAN communication
Engine Spd (NE Signal) Engine speed signal from ECM via direct line
Deceleration Sens Offset Val Deceleration sensor offset value
Deceleration Sens Calibration Deceleration sensor calibration status
Gradient of Road Surface Degree of road gradient
Battery Voltage Battery voltage
Battery Fluid Temperature Battery fluid temperature
Battery Temp (Start) Battery temperature at engine start
Engine Type Information Information on the engine type from the ECD system
Starter Type Starter assembly type
D Courtesy Switch Signal Driver door courtesy switch signal
Hood Courtesy Switch Hood courtesy switch signal
Neutral Switch Neutral position sensor (neutral position switch) signal
Clutch Upper SW Clutch start switch assembly (for upper) signal
Clutch Lower SW Clutch start switch assembly (for lower) signal
Starter Starter status
Starter Motor Starter motor status
TC Terminal TC and CG terminals of DLC3
Drive Mode Status Drive Mode Status
Cancel Switch Stop and start system cancel switch (combination switch assembly) signal
IG Switch Ignition or starter switch assembly*1 or push start switch*2 signal
Idle Engine idling status
Engine Start (IG SW) Engine start by ignition or starter switch assembly*1 or push start switch*2 operation
Stop Light SW (ECM) Stop light switch assembly signal from ECM
Stop Light SW (ABS/VSC) Stop light switch assembly signal from brake system
Fuel Heater Signal(ECD) Combustion type power heater signal
Engine Starter Signal Starter signal status
Buzzer Buzzer status
Indicat. Light Eco Stop and start indicator light status
Oil Prs Warn Light Prohibit Oil pressure warning light status
S&S Cancel Light Code Transmission code from the engine stop and start ECU to the combination meter assembly
Starter Operation # Number of starter operations (count record)
Number of Engine Starts (IG-ON) The number of starter operations by ignition or starter switch assembly*1 or push start switch*2 operation
Number of Engine Starts (Stop & Start) The number of starter operations by stop and start control
Number of Engine Starts (Clutch Released) The number of starter operations without clutch pedal being depressed
Number of Engine Starts (Clutch Half-Depressed) The number of starter operations with clutch pedal depressed halfway
Total Number of Engine Starts The number of times the engine starts
Vehicle Spd1 (ABS/VSC) Vehicle speed signal from skid control ECU (brake actuator assembly) through CAN communication
Steering Angle Steering wheel steering angle amount
Steering Angle Velocity Steering wheel turning speed
Steering Wheel Torque Steering wheel torque amount
Battery Current Battery current
Brake Boost Pressure Brake booster pressure (absolute pressure)
Brake Negative Pressure Brake booster vacuum (negative pressure)
Ambient Temp Sensor Ambient temperature
Stop&Start of Eng State Stop and start control status
Stop & Start A/C Mode Selected air conditioning mode (normal or stop and start priority control)
Idling Stop Rate Rate of the idling stop time to the entire ignition switch ON time
Total Idling Stop Rate Rate of the idling stop time to the entire ignition switch ON time
Integrated Current Battery integrated current
Cranking Time Engine cranking time (in current trip) (When minimum voltage is detected at engine start)
Min Voltage(Cranking) Minimum battery voltage when cranking engine
Min Volt(After Cranking) Minimum battery voltage just after engine cranking
Status of Battery Charge Control Battery charge control status
State of BBC Backup boost converter status
Atmosphere Pressure Atmospheric pressure (calculated value)
EPS Load Electric power steering current
Accelerator Position Accelerator pedal position
Engine OFF Request Engine stop request
Manual Start during S&S Manual start during stop and start control operation
Wrong Operation (Start) Wrong operation for engine start
Engine Reverse Rev. Engine reverse revolution status
N/Clutch Lower SW Abnoml Clutch switch assembly (for lower)
N/Clutch Upper SW Abnoml Clutch switch assembly (for upper)
Permit Idling Stop Engine stop standby
Running History Vehicle driving record
4WD Available Whether the vehicle is equipped with a 4 wheel drive control ECU
IPA Available Whether the vehicle is equipped with the intelligent parking assist function
Air Suspension Available Availability of air suspension system on vehicle
Welcab Available Availability of side left up seat system on vehicle
External BBC Available Availability of external backup boost converter on vehicle
Brake Hold Function Available Availability of brake hold function on vehicle
Steering Angle Sensor Available Availability of spiral with sensor cable subassembly on vehicle
Steering Angle Sensor Malfunction Whether a spiral with sensor cable subassembly malfunction exists
Steering Angle Sensor Circuit Open (+B) Whether there is an open to +B in the spiral with sensor cable subassembly circuit
Steering Angle Sensor Abnormal Value Whether there is an abnormality in the value continuously input from the spiral with sensor cable subassembly
Steering Torque Sensor Malfunction Whether a steering torque sensor malfunction exists
EPS Current Enable on Assist Whether the power steering assist current value is available
Auto A/C Availability of air conditioning system on vehicle
Cancel Switch (Multi-display) Available Stop and start system cancel switch installation information
Eng Start Req (A/C 2) Engine start request from the air conditioning system
Wheel Speed Malfunction Wheel speed malfunction status
Communication Method of Brake Boost Sensor Method of communication with vacuum sensor assembly
Communication Method of Brake Boost Sensor Method of communication with vacuum sensor
Oper Permission (Neutral Switch) Permission of stop and start control based on the neutral position sensor (neutral position switch) conditions
Oper Permission (Idling) Unused
Oper Permission (Vehicle Speed) Permission of stop and start control based on the vehicle speed conditions
Stop&Start Precondition Permission of stop and start control with all preconditions met
Stop&Start Precondition 2 Permission of stop and start control with all preconditions met
Oper Permission (ECM 1) Permission of stop and start control by the ECM
Oper Permission (ECM 2) Permission of stop and start control by ECD system
Oper Permission (IG SW) Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch*2 conditions
Oper Permission (DTC) Permission of stop and start control based on the DTC output conditions
Oper Permission (Brake Negative Pressure) Permission of stop and start control based on the brake booster vacuum conditions
Oper Permission (Interval) Permission of stop and start control based on the engine running time conditions
Oper Permission (D Door Closed) Permission of stop and start control based on the driver door open/close conditions
Oper Permission (Engine Hood Closed) Permission of stop and start control based on the engine hood open/close conditions
Oper Permission (A/C) Permission of stop and start control based on the air conditioning conditions
Oper Permission (Ambient Temperature) Permission of stop and start control based on the ambient temperature conditions
Oper Permission (After Running) Permission of stop and start control based on the initial trip conditions after the ignition switch is turned to ON
Oper Permission (Neutral SW OFF History) Permission of stop and start control based on the shift operation history
Oper Permission (Clutch Upper SW OFF History) Permission of stop and start control based on the clutch pedal operation history
Oper Permission (Battery) Permission of stop and start control based on the battery conditions
Oper Permission (Start Min Volt 1) Permission of stop and start control based on minimum voltage during starting when battery fluid temperature is 0°C (32°F) or less
Oper Permission (Start Min Volt 2) Permission of stop and start control based on minimum voltage during starting when battery fluid temperature is more than 0°C (32°F)
Oper Permission (Start Min Volt 3) Permission of stop and start control based on minimum voltage after cranking when battery fluid temperature is 0°C (32°F) or less
Oper Permission (Start Min Volt 4) Permission of stop and start control based on minimum voltage after cranking when battery fluid temperature is more than 0°C (32°F)
Oper Permission (Battery Current) Permission of stop and start control based on battery current
Oper Permission (Integrated Current) Permission of stop and start control based on the integrated current value conditions
Oper Prohibition (Jump Start) Prohibition of stop and start control based on the jump start conditions
Oper Prohibition (Manual Start) Prohibition of stop and start control based on the manual start conditions
Oper Permission (Interval For Starter) Permission of stop and start control based on the conditions after engine restart
Oper Permission (Cancel Switch) Permission of stop and start control based on the stop and start system cancel switch (combination switch assembly) operation
Oper Permission (Road Surface Gradient) Permission of stop and start control based on the road grade conditions
Oper Permission (Driver Side Buckle SW) Permission of stop and start control based on the driver seat belt condition
Oper Permission (Steering) Permission of stop and start control by the power steering ECU assembly
Oper Permission (4WD and Rear Differential Lock) Stop and start control permission status based on driving mode
Oper Permission (Key Operation) Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch*2 operation
Oper Permission (Starter Check Complete) Permission of stop and start control based on the starter circuit self-check result
Oper Prohibition (Engine F/C) Prohibition of stop and start control based on the engine fuel-cut prohibition signal
Eng Start Req (Brk Negative Pressure Low) Engine start request due to low brake booster vacuum
Eng Start Req (IG Switch) Engine start request due to ignition or starter switch assembly*1 or push start switch*2 operation
Eng Start Req (ECM) Engine start request from ECM
Eng Start Req (A/C) Engine start request from air conditioning system
Eng Start Req (Steering) Engine start request by the power steering system
Eng Start Req (Detect DTC) Engine start request due to output of DTCs
Eng Start Req (Clutch Pedal) Engine start request due to clutch pedal operation
Eng Start Req (Clutch Lower SW) Engine start request by the clutch start switch assembly
Eng Start Req (Engine Hood Open) Engine start request due to opening of engine hood
Eng Start Req (Battery Condition) Engine start request based on battery performance
Eng Start Req (CVT Vehicle Speed) Engine start request based on vehicle speed signal from continuously variable transaxle system
Eng Start Req (ABS Vehicle Speed) Engine start request based on vehicle speed signal from the brake system
Eng Start Req(Cancel SW) Engine start request by stop and start system cancel switch (combination switch assembly)
Eng Start Req(Courtesy SW or Buckle SW) Engine start request by courtesy switch (driver side) or driver side buckle switch
Eng Start Req (4WD and Rear Differential Lock) Engine start request when the vehicle is switched to 4WD or rear differential is locked while the engine is stopped due to stop and start control
ABS Running Engine start request from vehicle stability control system
Clutch SW Signal Abnoml Malfunction in the clutch start switch assembly
Crank Pos Sen Abnoml 3 Fail-safe operation due to abnormal engine speed signal
N Position Switch Neutral position sensor (neutral position switch) status
Brk Boost Sen Abnoml 1 Malfunction in the vacuum sensor assembly
Brk Boost Sen Abnoml 2 Malfunction in the vacuum sensor assembly
Brk Boost Sen Abnoml 3 Malfunction in the vacuum sensor assembly
Starter Count Abnoml Error in the number of starter operations
Starter Circuit Abnoml Malfunction in the starter circuit
Starter Circuit Open Open in the starter circuit (STA malfunction)
Alternator Status Generator power generation status
BBC Abnoml Malfunction in the backup boost converter
BBC Overcurrent Overcurrent in boosting output from the backup boost converter
BBC Duty Abnormal duty of the backup boost converter
BBC Power Low Decrease in backup boost converter output
BBC Over Heat Overheating of the backup boost converter
BBC Thermistor Malfunction in the backup boost converter thermistor
IG SW Abnoml Malfunction in the ignition or starter switch assembly*1 or push start switch*2
Battery Abnoml Malfunction in the power source
Comm Err with ECM Communication error with the ECM
Comm Err with ABS/VSC Communication error with the skid control ECU (brake actuator assembly)
Comm Err with EPS Communication error with the power steering ECU assembly
Comm Err with J/B Communication error with the main body ECU (multiplex network body ECU)
Comm Err with A/C Communication error with the air conditioning amplifier assembly
Comm Err with Air Bag Communication error with the center airbag sensor assembly
Comm Err with Meter Communication error with the combination meter assembly
Comm Err with Steering Angle Sensor Communication error with the spiral with sensor cable sub-assembly
CPU Duty Error in CPU duty
EEPROM Error in EEPROM
Dec Sensor Calibration Deceleration sensor zero point uncalibrated
Deceleration Sensor Movement Sticking of the deceleration sensor
Engine Stall Engine stall history
Engine Stall History during S&S (Hood Open) History of engine stall caused by depressing the clutch pedal with the engine hood open while the engine is stopped by stop and start control (shift lever in neutral)
Engine Stall History during S&S (Collision or Battery Voltage Low) History of engine stall due to a collision or low battery voltage when the stop and start control is operating
Engine Stall History during Engine Starting (Collision) History of engine stall due to a collision while the engine is stopped by stop and start control
Engine Start Fail History of engine restart failure by stop and start control
Voltage Judgment Error in voltage judgment
AD Converter Malfunction Malfunction in the Analog to Digital converter
Starter Relay Overcurrent Overcurrent in the starter relay
NE Sensor Circuit Open2 Malfunction in the crankshaft position sensor circuit
Brk Boost Malfunc 1 Fail-safe operation due to malfunction in vacuum sensor assembly
Brk Boost Malfunc 2 Fail-safe operation due to malfunction in vacuum sensor assembly
N Position Voltage Status Malfunction in the neutral position sensor (neutral position switch)
Num of Current Code Number of currently stored DTCs

*1: w/o Entry and Start System

*2: w/ Entry and Start System