Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  U0100  Lost Communication with ECM / PCM "A"  U0121  Lost Communication with Anti-lock Brake System (ABS) Control Module  U0126  Lost Communication With Steering Angle Sensor Module  U0131  Lost Communication with Power Steering Control Module  U0140  Lost Communication with J/B ECU  U0151  Lost Communication with SRS Airbag ECU  U0155  Lost Communication with Instrument Panel Cluster Control Module (Combination Meter)  U0164  Lost Communication with HVAC Control Module  


DESCRIPTION

The engine stop and start ECU communicates with the SFI system, vehicle stability control system, power steering system, air conditioning system, airbag system, meter / gauge system and main body ECU (multiplex network body ECU) via CAN communication.

If there is a communication error between the engine stop and start ECU and any of the systems, the engine stop and start ECU stores DTCs and illuminates the stop and start cancel indicator light except when there is a communication error with the meter/gauge system.

HINT:
·

When there is an open in the output side of the backup boost converter (built into the engine stop and start ECU), power to the system with the open is cut off. The engine stop and start ECU stores CAN communication DTCs for the system with the open and stop and start system DTC P323B.

·

When the backup boost converter (built into the engine stop and start ECU) detects overcurrent in any of the circuits it supplies power to, it shuts off the circuit. The engine stop and start ECU stores CAN communication DTCs for the system which circuit was shut off and stores stop and start system DTC B22C0.

e.g.: When the backup boost converter (built into the engine stop and start ECU) detects overcurrent in the power source circuit of the power steering system and cuts off power supply, the engine stop and start ECU stores DTCs U0131 and B22C0.



DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
U0100 Lost Communication with ECM / PCM "A" No communication between the engine stop and start ECU and ECM for 0.76 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

ECM


Blinks DTC stored
U0121 Lost Communication with Anti-lock Brake System (ABS) Control Module No communication between the engine stop and start ECU and brake actuator assembly for 2.22 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Brake actuator assembly


Blinks DTC stored
U0126 Lost Communication With Steering Angle Sensor Module No communication between the engine stop and start ECU and the spiral with sensor cable sub-assembly for 0.72 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Spiral with sensor cable sub-assembly


Blinks DTC stored
U0131 Lost Communication with Power Steering Control Module No communication between the engine stop and start ECU and the power steering ECU assembly for 0.8 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Power steering ECU assembly


Blinks DTC stored
U0140 Lost Communication with J/B ECU No communication between the engine stop and start ECU and the main body ECU (multiplex network body ECU) for 3.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Main body ECU (multiplex network body ECU)


Blinks DTC stored
U0151 Lost Communication with SRS Airbag ECU No communication between the engine stop and start ECU and airbag sensor assembly for 10.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Center airbag sensor assembly


Blinks DTC stored
U0155 Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) No communication between the engine stop and start ECU and the combination meter assembly for 10.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Combination meter assembly


Blinks DTC stored
U0164 Lost Communication with HVAC Control Module No communication between the engine stop and start ECU and the air conditioning amplifier assembly for 10.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Air conditioning amplifier assembly


Blinks DTC stored

CAUTION / NOTICE / HINT

HINT:

If any of CAN communication system DTCs and sensor malfunction DTCs related to the CAN communication system are output simultaneously, perform troubleshooting for the CAN communication system DTCs first, then for the sensor malfunction DTCs.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the ignition switch off and wait for 30 seconds or more.


b.

Turn the ignition switch to ON.


c.

Start the engine.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


f.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Result Proceed to
DTC U0100, U0121, U0123, U0126, U0131, U0140, U0151, U0155, U0164 or U1106 is output A
DTC U0100, U0121, U0123, U0126, U0131, U0140, U0151, U0155, U0164 or U1106 is not output B




A

B