Home › Power Source / Network › 3ZR-FE BATTERY / CHARGING › GENERATOR(for 130 A Type) › from 2015.10
RM3090E _57 Power Source / Network _008412 3ZR-FE BATTERY / CHARGING _0208765 GENERATOR(for 130 A Type) A

3ZR-FE BATTERY / CHARGING  GENERATOR(for 130 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A287135

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A204355C11
2.198,1.396 2.198,0.896 true 1.167,1.083 1.833,1.833 1.833,1.833 2.083,1.833 true 1.563,0.865 1.833,0.167 1.833,0.167 3,0.667 true 1.75,0.167 1.833,0.167 true 2.135,1.417 2.438,1.604 0.302,0.188 10 false *a 1.313,0.083 1.833,0.26 0.521,0.177 10 false SST A 2.125,1.75 2.646,1.927 0.521,0.177 10 false SST B
*a Generator Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



c.
A204356C10
2.156,0.771 2.333,0.5 2.333,0.5 2.5,0.5 false 1.917,0.573 2.083,0.25 2.083,0.25 2.25,0.25 false 1.771,1.833 2.083,1.99 0.313,0.156 10 false *a 2.531,0.417 3.302,0.615 0.771,0.198 10 false SST A 2.281,0.167 3.052,0.365 0.771,0.198 10 false SST B
*a Hold
V100135

Turn


Using a wrench to hold SST A, turn SST B counterclockwise to loosen the generator pulley with clutch.

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator assembly.


e.

Remove the generator pulley with clutch from the generator rotor shaft.


f.

Remove the generator assembly from a vise.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A285299

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387B 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A282133

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A285301

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A292391

Remove the 4 bolts.


b.
A153383C13
1.114,1.723 1.409,1.879 0.295,0.156 10 SST 2.721,0.599 3.011,0.744 0.289,0.145 10 SST 0.573,0.516 0.756,0.675 0.183,0.159 10 *a 1.067,1.801 0.993,1.801 0.993,1.801 0.654,1.588 false 2.666,0.686 2.56,0.686 2.56,0.686 2.094,0.855 false
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27444 7.REMOVE GENERATOR BEARING COVER PACKING

a.
A284548

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 8.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A153384

Remove the generator rotor assembly.


Hide 27310B 9.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A153387

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 10.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A153385

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A153386N18
2.5,1.146 1.917,0.25 1.917,0.25 2.573,0.896 true 1.063,1.365 0.438,1.771 0.438,1.771 1.021,1.188 true 1.625,0.167 2.083,0.365 0.458,0.198 10 false SST 0.198,1.771 0.656,1.969 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)