Home › Engine / Hybrid System › 2WW ENGINE MECHANICAL › ENGINE UNIT › from 2015.10
RM3090E _51 Engine / Hybrid System _044373 2WW ENGINE MECHANICAL _0211289 ENGINE UNIT G

2WW ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13540 1.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A318400C01
0.74,1.698 0.99,1.698 0.99,1.698 1.323,1.365 true 0.521,1.583 0.833,1.781 0.313,0.198 10 false *a
*a Plunger


Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 2.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A318399C01
0.75,1.927 1,1.927 1,1.927 1.083,1.427 true 0.521,1.833 0.833,2.031 0.313,0.198 10 false *a
*a Plunger


Push the plunger and check that it moves smoothly.

If necessary, replace the No. 2 chain tensioner assembly.


Hide 16630G 3.INSPECT IDLER PULLEY ASSEMBLY

a.
A319689

Check that the idler pulley assembly turns smoothly.

If necessary, replace the idler pulley assembly.


Hide 13511 4.INSPECT CAMSHAFT

a.

Check the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the camshaft.



Hide 13512 5.INSPECT NO. 2 CAMSHAFT

a.

Check the No. 2 camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the No. 2 camshaft.



Hide 15709 6.INSPECT NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A319680

Check the No. 2 oil nozzle sub-assembly for damage or clogging.

If there is damage or clogging, replace the No. 2 oil nozzle sub-assembly.


Hide 13801 7.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A318413

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Use only clean engine oil.



a.

Place the valve lash adjuster assembly into a container full of new engine oil.


b.

Insert SST tip into the valve lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

A271553C03
1.083,0.833 1.417,0.833 true 1.083,1.094 1.417,1.094 true 1.094,1.354 1.427,1.354 true 1.052,1.813 1.385,1.813 true 0.979,2.188 1.313,2.188 true 0.958,2.375 1.417,2.583 1.417,2.583 1.583,2.583 true 4.219,1.115 4.469,1.115 4.469,1.115 4.885,1.615 true 2.333,2.167 2.917,2.167 true 2.25,1.833 2.917,1.833 true 0.833,0.083 1.146,0.281 0.313,0.198 10 false *a 2.25,0.063 2.563,0.26 0.313,0.198 10 false *b 1.51,1.021 1.823,1.188 0.313,0.167 10 false *c 1.5,1.292 1.813,1.49 0.313,0.198 10 false *d 1.448,1.729 1.76,1.927 0.313,0.198 10 false *e 3.021,2.135 3.333,2.333 0.313,0.198 10 false *f 1.688,2.5 2,2.698 0.313,0.198 10 false *g 3.885,1.031 4.531,1.281 0.646,0.25 10 false SST 3.021,1.75 3.667,2 0.646,0.25 10 false SST 1.5,0.75 2.146,1 0.646,0.25 10 false SST 1.417,2.125 1.729,2.323 0.313,0.198 10 false *f
*a Correct *b Incorrect
*c Taper Port *d Plunger
*e Lower Pressure Chamber *f Check Ball
*g High Pressure Chamber - -


SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding air, remove SST. Then quickly and firmly press the plunger repeatedly with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster assembly with a new one.