Home › Drivetrain › K114 MULTIDRIVE / CVT › SHIFT LEVER › from 2015.10
RM3090E _52 Drivetrain _044380 K114 MULTIDRIVE / CVT _0212490 SHIFT LEVER G

K114 MULTIDRIVE / CVT  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LEVER ASSEMBLY (w/o Smart Key System)

a.
C278979C01
1.698,1.615 1.167,1.042 1.167,1.042 1.01,1.042 true 1.688,1.875 1.521,2.875 1.521,2.875 1.396,2.875 true 2.052,1.875 2.25,2.865 2.25,2.865 2.365,2.865 true 2.042,1.604 2.26,0.875 2.26,0.875 2.375,0.875 true 0.042,0.063 0.354,0.26 0.313,0.198 10 *a 0.813,0.969 1.031,1.146 0.219,0.177 10 IG 1.104,2.792 1.417,2.99 0.313,0.198 10 STP 2.406,2.781 2.781,2.979 0.375,0.198 10 KLS+ 2.427,0.802 2.74,1 0.313,0.198 10 ACC
*a Component with harness connected
(Shift Lever Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ON 11 to 14 V
Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
4 (IG) - Body - ground Ignition switch to ON 11 to 14 V
Ignition switch off Below 1 V


HINT:

Do not disconnect the shift lever assembly connector.


If the voltage value is not as specified, replace the shift lever assembly.


b.
C278979C02
1.396,2.917 1.531,2.917 1.531,2.917 1.802,1.875 true 0.042,0.031 0.354,0.229 0.313,0.198 10 *a 1.281,2.844 1.427,3.01 0.146,0.167 10 E
*a Component with harness connected
(Shift Lever Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the shift lever assembly connector.


If the resistance value is not as specified, replace the shift lever assembly.


Hide 2.INSPECT SHIFT LEVER ASSEMBLY (w/ Smart Key System)

a.
C278979C03
1.698,1.615 1.167,1.042 1.167,1.042 1.01,1.042 true 1.688,1.875 1.521,2.875 1.521,2.875 1.396,2.875 true 1.927,1.604 1.76,0.896 1.76,0.896 1.656,0.896 true 2.042,1.604 2.26,0.875 2.26,0.875 2.375,0.875 true 0.042,0.063 0.354,0.26 0.313,0.198 10 *a 0.802,0.969 1.042,1.146 0.24,0.177 10 IG 1.104,2.792 1.417,2.99 0.313,0.198 10 STP 1.458,0.813 1.833,1.01 0.375,0.198 10 P2 2.427,0.802 2.74,1 0.313,0.198 10 ACC
*a Component with harness connected
(Shift Lever Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
2 (P2) - Body ground Engine switch on (ACC) and shift lever not in P Below 1 V
Engine switch on (ACC) and shift lever in P 11 to 14 V
4 (IG) - Body - ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


HINT:

Do not disconnect the shift lever assembly connector.


If the voltage value is not as specified, replace the shift lever assembly.


b.
C278979C02
1.396,2.917 1.531,2.917 1.531,2.917 1.802,1.875 true 0.042,0.031 0.354,0.229 0.313,0.198 10 *a 1.281,2.844 1.427,3.01 0.146,0.167 10 E
*a Component with harness connected
(Shift Lever Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the shift lever assembly connector.


If the resistance value is not as specified, replace the shift lever assembly.


Hide 3.INSPECT TRANSMISSION CONTROL SWITCH

a.

Disconnect the connector from the shift lever assembly.


b.
C277025C06
0.802,1.802 1.219,1.385 true 1.344,1.781 1.479,1.396 true 1.771,1.792 1.76,1.385 true 2.177,1.771 2.031,1.385 true 2.635,1.771 2.292,1.396 true 1.26,1.833 1.573,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.698,0.5 1.01,0.698 0.313,0.198 10 false *a 1.594,1.833 2.052,2.031 0.458,0.198 10 false SFTU 2.167,1.833 2.625,2.031 0.458,0.198 10 false E 2.531,1.833 2.99,2.031 0.458,0.198 10 false SFTD 0.104,0.104 0.479,0.344 0.375,0.24 10 false *A
*A for LHD
*a Component with harness connected
(Transmission control switch)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher


If the resistance value is not as specified, replace the shift lever assembly.


c.
C277025C07
0.802,1.802 1.219,1.385 true 1.344,1.781 1.479,1.396 true 1.771,1.792 1.76,1.385 true 2.177,1.771 2.031,1.385 true 2.635,1.771 2.292,1.396 true 1.26,1.833 1.573,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.698,0.51 1.01,0.708 0.313,0.198 10 false *a 1.594,1.833 2.052,2.031 0.458,0.198 10 false SFTD 2.167,1.833 2.625,2.031 0.458,0.198 10 false E 2.531,1.833 2.99,2.031 0.458,0.198 10 false SFTU 0.104,0.104 0.479,0.344 0.375,0.24 10 false *A
*A for RHD
*a Component with harness connected
(Transmission control switch)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher


If the resistance value is not as specified, replace the shift lever assembly.