Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE FLUID › from 2015.10
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051013 CONTINUOUSLY VARIABLE TRANSAXLE FLUID N

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The K111F continuously variable transaxle assembly does not have an oil filler tube or oil level gauge. When adding fluid, add fluid through the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

When adding fluid, add the specified amount of fluid while the engine is cold. Then, warm up the engine to circulate the fluid in the transaxle and adjust the fluid level with the engine idling at the specified fluid temperature.


c.

The K111F continuously variable transaxle requires Toyota Genuine CVT fluid FE.


d.

When adjusting the fluid level, park the vehicle on level ground. Make sure that the longitudinal tilt of the vehicle is not more than 1°.


e.

When adjusting the fluid level, turn off all electrical devices, such as the air conditioning, headlights and electric fan, to reduce electrical load.


f.

The fluid temperature in the text indicates "A/T Oil Temperature 1" displayed on the GTS.


g.

Perform the adjustment according to the following procedures and notes.

C202513E14
1.875,2.333 2.719,2.594 2.719,2.594 2.719,2.708 false 5.625,2.385 6.135,2.656 6.135,2.656 6.135,2.813 false 1.552,3.396 4.271,3.76 2.719,0.365 12 3. ADJUST FLUID TEMPERATURE 0.302,5.781 2.25,6.125 1.948,0.344 12 4. ADJUST FLUID LEVEL 0.063,0 2.146,0.344 2.083,0.344 12 Fluid Filling Procedure: 0.063,0.344 2.313,1.073 2.25,0.729 12 1. PERFORM INITIAL FILLING (when necessary) 4.021,0.344 7.083,0.573 3.063,0.229 12 2. ADD SPECIFIED AMOUNT OF FLUID 0.052,1.083 2.01,1.26 1.958,0.177 10 Add fluid to the specified level. 4.208,0.792 6.875,1.104 2.667,0.313 10 Add the correct amount of fluid specified for the operation that was performed. 0.219,2.552 1.354,3.563 1.135,1.01 10 Add fluid until fluid comes out of the overflow plug hole. 0.146,7.708 1.927,8.708 1.781,1 10 Keep the overflow plug open until the fluid flow slows and only drops come out. 0.302,6.188 2.688,6.667 2.385,0.479 10 Drain excess fluid at the specified fluid temperature. 4.281,6.073 6.708,6.719 2.427,0.646 10 If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.542,3.813 6.885,4.552 5.344,0.74 10 Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 6.365,1.771 7.042,2.323 0.677,0.552 10 Specified Amount of Fluid 2.094,2.698 3.333,3.302 1.24,0.604 10 No. 1 Transmission Oil Filler Tube 5.729,2.823 6.635,3.021 0.906,0.198 10 Overflow Plug


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedures referenced in the work flow below.

C275733E02
0.219,0.979 2.427,1.313 2.208,0.333 10 false Operations that require initial filling: 0.302,1.344 3.24,1.625 2.938,0.281 8 false Removal and installation of the front drive shaft assembly. 0.313,1.656 1.885,1.823 1.573,0.167 8 false Draining and refilling fluid. 0.313,1.958 3.073,2.229 2.76,0.271 8 false Removal and installation of the transmission oil cooler. 0.323,2.302 3.323,2.583 3,0.281 8 false Removal and installation of the torque converter assembly. 0.333,2.656 3.875,2.938 3.542,0.281 8 false Removal and installation of the transaxle oil pan sub-assembly. 0.323,3.021 3.208,3.313 2.885,0.292 8 false Changing the continuously variable transaxle assembly. 3.906,0.979 6.521,1.313 2.615,0.333 10 false Operations that do not require initial filling: 3.969,1.438 5.365,1.729 1.396,0.292 8 false Repair of a fluid leak, etc. 0.115,0.063 1.146,0.427 1.031,0.365 10 false WORKFLOW: 3.396,0.073 3.906,0.375 0.51,0.302 10 false START 2.677,0.594 4.531,0.938 1.854,0.344 10 false [STEP 4] Perform Initial Filling 2.5,3.646 4.948,3.969 2.448,0.323 9 false [STEP 5] Add Specified Amount of Fluid 2.563,4.219 4.792,4.563 2.229,0.344 10 false [STEP 6] Adjust Fluid Temperature 1.323,4.698 5.917,5.052 4.594,0.354 10 false Enter fluid temperature detection mode and engine idle speed control mode 2.854,5.26 4.396,5.594 1.542,0.333 10 false Idling (Warm up the fluid) 3.135,5.802 4.104,6.479 0.969,0.677 10 false Check the fluid temperature 2.542,6.646 4.667,6.969 2.125,0.323 10 false Fluid level adjustment temperature 1.313,5.979 2.75,6.635 1.438,0.656 10 false Below fluid level adjustment temperature 4.198,5.969 5.667,6.635 1.469,0.667 10 false Above fluid level adjustment temperature 5.906,5.26 6.99,6.146 1.083,0.885 10 false Stop the engine and wait until the fluid temperature drops 2.76,7.229 4.448,7.542 1.688,0.313 10 false [STEP 7] Adjust Fluid Level 3.031,7.635 4.156,7.938 1.125,0.302 10 false Drain excess fluid 2.854,8.208 4.438,8.552 1.583,0.344 10 false Check the amount of fluid 2.906,8.896 4.344,9.26 1.438,0.365 10 false [STEP 8] Rebuild Work 3.469,9.479 3.813,9.719 0.344,0.24 10 false END 0.333,8.198 0.917,8.5 0.583,0.302 10 false Add fluid 1.292,8.375 2.469,8.688 1.177,0.313 10 false No fluid comes out 4.885,8.375 5.958,8.688 1.073,0.313 10 false Fluid comes out 6.385,8.188 6.958,8.448 0.573,0.26 10 false Overflow 3.969,1.677 6.052,2.26 2.083,0.583 8 false Installation of a new transaxle assembly. (with new torque converter assembly) 3.969,1.198 6.802,1.396 2.833,0.198 8 false Disconnection of the oil cooler or cooler hose.


Hide 3. BEFORE FILLING TRANSAXLE WITH FLUID

NOTICE:

If the transaxle is hot (fluid temperature is high), wait until the fluid temperature is the same as the ambient temperature before starting the following procedure (recommended fluid temperature: approximately 20°C [68°F])


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the longitudinal tilt of the vehicle is not more than 1°).



b.

Remove the No. 1 engine under cover and rear engine under cover LH.


Hide 4. PERFORM INITIAL FILLING

NOTICE:

After performing any of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the Add Specified Amount of Fluid procedure (Step 5).


Operations that do not Require Initial Filling
·

Disconnection of the oil cooler or oil cooler hose.

·

Repair of a fluid leak, etc.

·

Installation of a new transaxle.



a.
C279060

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C279061

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.

NOTICE:
·

If fluid comes out after removing the overflow plug, wait until the fluid flow slows and only drops come out.

·

If fluid comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C279062C02
2.583,0.823 2.833,0.396 2.833,0.396 2.948,0.396 false 2.99,0.323 3.302,0.521 0.313,0.198 10 *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm socket hexagon wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the hexagon socket into the overflow plug hole.



d.

Perform initial filling.

i.
C279063

Fill fluid into the refill hole until it flows out from the overflow plug hole.

NOTICE:

Use Toyota Genuine CVT fluid FE.




e.
C279064

Wait until the fluid flow slows and only drops come out.


f.

Temporarily install the overflow plug.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.

Remove the refill plug and gasket from the continuously variable transaxle assembly (when initial filling is not performed).


b.

Fill fluid into the refill hole with the correct amount of fluid as listed in the table below.

NOTICE:

The refill amount differs depending on the operation that was performed.


Standard Capacity:
Operation Performed Fill Amount
·

Disconnection of the oil cooler or cooler hose.

·

Repair of a fluid leak, etc.


0.6 liters (0.6 US qts, 0.5 Imp. qts)
Installation of a new transaxle (use of new torque converter). 6.2 liters (6.6 US qts, 5.5 Imp. qts)
Installation of a new transaxle (reuse of torque converter). 5.6 liters (5.9 US qts, 4.9 Imp. qts)
·

Removal and installation of the drive shaft.

·

Removal and installation of the oil pan.


2.1 liters (2.2 US qts, 1.8 Imp. qts)
Removal and installation of a torque converter (use of new torque converter). 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Removal and installation of a torque converter (reuse of torque converter). 2.9 liters (3.1 US qts, 2.6 Imp. qts)



c.
C279060

Temporarily install the refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



d.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE

a.

When using the GTS:

i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON and turn the GTS on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.


v.

According to the display on the GTS, perform the Active Test "Connect the TC and TE1".

HINT:

The indicator lights on the combination meter blink to indicate the DTC output when Active Test "Connect the TC and TE1 / ON" is performed.




b.

When not using the GTS:

i.
C166029C53
1.594,0.854 1.792,0.313 1.792,0.313 1.896,0.313 false 1.781,1.448 1.656,1.813 1.656,1.813 1.542,1.813 false 1.271,1.729 1.51,1.906 0.24,0.177 10 TC 1.938,0.229 2.302,0.406 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  



c.

Depress and hold the brake pedal.


d.

Start the engine.

NOTICE:

Make sure that electrical systems, such as the air conditioning system, audio system and lighting system, are off.



e.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transaxle.



f.

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



g.
C329010C02
0.031,0.042 0.271,0.24 0.24,0.198 10 true *A 0.042,2.469 0.281,2.656 0.24,0.188 10 true *B
*A w/ Multi-information Display
*B w/o Multi-information Display


Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator in the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the step where the terminals are first connected and perform the procedure again.




h.

Move the shift lever from N to P.


i.

Release the brake pedal.


j.

Disconnect the terminals of the DLC3.

i.

When using the GTS.

Enter the following menus: Connect the TC and TE1 / OFF.


ii.

When not using the GTS.

Remove SST from terminals 13 (TC) and 4 (CG).

NOTICE:

Make sure that the terminals are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting the terminals activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature reaches the specified temperature and the engine speed is maintained.

·

Even after the terminals are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.





k.

Adjust the fluid temperature to the normal operating temperature.

i.

Check the fluid temperature by the D shift indicator.

HINT:
·

In the fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the normal operating temperature range).




ii.

Adjust the fluid temperature.

·

If the D shift indicator is off [Below Normal Operating Temperature: 30°C (86°F) or less]: Warm up the engine with the engine idling in the engine idle speed control mode until the D shift indicator turns on.


·

If the D shift indicator is on [Normal Operating Temperature: 30 to 40°C (86 to 104°F)]: Immediately proceed to the Adjust Fluid Level procedure (Step 7).


·

If the D shift indicator blinks [Above Normal Operating Temperature: 40°C (104°F) or higher]: Stop the engine and wait until the fluid temperature drops to 30°C (86°F) or less (the D shift indicator goes off). Then perform the Adjust Fluid Temperature procedure again from the beginning.


The Relationship between Normal Operating Temperature and the D Shift Indicator:
Below Normal Operating Temperature Normal Operating Temperature Above Normal Operating Temperature
Fluid Temperature ("A/T Oil Temperature 1" displayed on the GTS) 30°C or less (86°F or less) 30 to 40°C (86 to 104°F) 40°C or higher (104°F or higher)
D Shift Indicator Off On Blinks




Hide 7.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the longitudinal tilt of the vehicle is not more than 1°).



b.
C279061

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



c.

Check the amount of fluid that comes out of the overflow plug hole.

·

If the amount of fluid that comes out of the overflow plug hole is large, proceed to *1.

·

If no fluid comes out of the overflow plug hole, proceed to *2.


NOTICE:

If only a small amount of fluid (approximately 5 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.



d.
C279063

*2: If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drops come out.

NOTICE:

Use Toyota Genuine CVT fluid FE.



e.
C279065

*1: If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drops come out.

HINT:

The fluid flow will not completely stop because the fluid expands as its temperature increases.



f.
C279061

Install a new gasket and the overflow plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.
C279060

Install a new gasket and the refill plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


h.

Lower the vehicle.


i.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits fluid temperature detection mode.



j.

Remove the GTS from the DLC3 (when using the GTS).


Hide 8. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the No. 1 engine under cover and rear engine under cover LH.


e.

Lower the vehicle.