Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) U

STOP AND START  STOP AND START SYSTEM(for 2WW)  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A375785E01
1.51,0.135 1.938,0.427 0.427,0.292 3.156,0.125 3.583,0.417 0.427,0.292 4.948,0.125 5.375,0.417 0.427,0.292 5.51,1.948 5.938,2.24 0.427,0.292 3.188,1.969 3.615,2.26 0.427,0.292 1.094,2 1.521,2.292 0.427,0.292 1.594,0.198 1.969,0.396 0.375,0.198 10 false A86 3.25,0.188 3.625,0.385 0.375,0.198 10 false A66 5.031,0.188 5.406,0.385 0.375,0.198 10 false G87 1.167,2.063 1.542,2.26 0.375,0.198 10 false A86 3.25,2.031 3.625,2.229 0.375,0.198 10 false A66 5.583,2.021 5.958,2.219 0.375,0.198 10 false G87

a.

Disconnect the A86, A66 and G87 engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A86-1 (BIN2) - Body ground R - Body ground Battery Always 9.5 to 14 V
A86-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
A86-3 (BIN1) - Body ground L - Body ground Battery Always 9.5 to 14 V
A86-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-1 (+B) - Body ground B - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A66-6 (DGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-10 (NE) - Body ground P - Body ground Engine speed signal from ECM Always 10 kΩ or higher
G87-13 (CANH) - Body ground LG - Body ground CAN communication Always 200 Ω or higher
G87-14 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G87-18 (IG2) - Body ground V - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - Body ground for LHD: L - Body ground
for RHD: W - Body ground
Ignition switch signal Ignition switch ACC 9.5 to 14 V
G87-21 (IG1) - Body ground L - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the A86, A66 and G87 engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A66-3 (BRE2) - Body ground G - Body ground Ground (vacuum sensor assembly) Always Below 1 Ω
A66-7 (BNT1) - A66-6 (DGND) B - W-B Engine hood courtesy switch (Hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A66-8 (TMN) - A66-25 (TME2) L - BR Neutral position sensor (Neutral position switch) signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
A66-10 (NE) - A66-6 (DGND) P - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 1)
A66-11 (CLU) - A66-6 (DGND) L - W-B Clutch start switch assembly (for upper) signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A66-13 (PB) - A66-3 (BRE2) SB - G Vacuum sensor assembly signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied to vacuum sensor assembly


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (450 mmHg, 17.7 in.Hg) applied to vacuum sensor assembly


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly


3.4 to 3.8 V
A66-14 (BRVC) - A66-6 (DGND) L - W-B Vacuum sensor assembly power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A66-17 (CLL) - A66-6 (DGND) W - W-B Clutch start switch assembly (for lower) signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A66-21 (STA) - A66-6 (DGND) LG - W-B Starter pinion operation signal Cranking 6.0 V or more
A66-26 (TMVC) - A66-6 (DGND) G - W-B Neutral position sensor (Neutral position switch) power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
G87-1 (IG31) - A66-6 (DGND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-2 (B41) - A66-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
G87-3 (IG41) - A66-6 (DGND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-4 (CHI)* - A66-6 (DGND) R - W-B Combustion type power heater system operating signal
·

Ignition switch ON

·

Heater switch assembly on


9.5 to 14 V
·

Ignition switch ON

·

Heater switch assembly off


Below 1 V
G87-5 (ECAN) - A66-6 (DGND) R - W-B Stop and start system cancel switch signal
·

Ignition switch ON

·

Stop and start system cancel switch pressed


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch not press


8 to 14 V
G87-6 (IG11) - A66-6 (DGND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-10 (IG12) - A66-6 (DGND) P - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-12 (B42) - A66-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
G87-18 (IG2) - A66-6 (DGND) V - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - A66-6 (DGND) for LHD: L - W-B
for RHD: W - W-B
Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
G87-21 (IG1) - A66-6 (DGND) L - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-24 (AC41) - A66-6 (DGND) G - W-B Backup boost converter signal Ignition switch ACC 10.5 to 16 V

*: w/ Combustion Type Power Heater System



e.
A318633E03
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Waveform 1

Item Content
Tester Connection A66-10 (NE) - A66-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up