Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P060A  Internal Control Module Monitoring Processor Performance  


DESCRIPTION

The engine stop and start ECU can detect open circuits when signals such as the boost, standby request or overheating signal cannot be sent to the backup boost converter control IC from the stop and start control IC in the engine stop and start ECU.

If a CPU duty malfunction is detected, the engine stop and start ECU stores DTC P060A and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P060A Internal Control Module Monitoring Processor Performance The following condition continues for 1 second or more (2 trip detection logic):
·

CPU duty malfunction is detected.


·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

for CVT:

Depress the brake pedal and stop the vehicle.

for Manual Transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more. (for CVT: Keep the shift lever in D.)


h.

for CVT:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transaxle:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

for CVT:

Depress the brake pedal and stop the vehicle.

for Manual Transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for CVT: Keep the shift lever in D.)


f.

for CVT:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transaxle:

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A375331E01
5.906,1 6.521,1.198 0.615,0.198 10 false BIN1 3.448,1.188 3.906,1.385 0.458,0.198 10 false BBC 5.677,0.885 5.833,1.083 0.156,0.198 10 false 3 5.677,0.219 5.833,0.417 0.156,0.198 10 false 1 3.833,0.51 4.979,0.729 1.146,0.219 10 false BBC NO. 2 1.01,1.563 2.083,1.76 1.073,0.198 10 false Battery 0.802,0.792 1.875,0.99 1.073,0.198 10 false FL MAIN 5.885,1.281 6.5,1.479 0.615,0.198 10 false GND1 5.896,1.542 6.51,1.74 0.615,0.198 10 false GND2 5.677,1.438 5.833,1.635 0.156,0.198 10 false 2 5.677,1.156 5.833,1.354 0.156,0.198 10 false 8 5.896,0.344 6.51,0.542 0.615,0.198 10 false BIN2 5.271,1.802 5.729,2 0.458,0.198 10 false A86 5.271,2.021 7.01,2.25 1.74,0.229 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

for CVT:

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

for Manual Transaxle:

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY)
a.

Disconnect the engine stop and start ECU connector.


b.
A348176C11
0.188,0.99 0.531,1.26 0.344,0.271 0.646,1.823 1.198,1.281 true 1.531,1.844 1.25,1.521 true 0.219,0.219 0.531,0.417 0.313,0.198 10 false *a 0.448,1.875 0.76,2.073 0.313,0.198 10 false BIN2 1.469,1.854 1.781,2.052 0.313,0.198 10 false BIN1 0.24,1.042 0.552,1.24 0.313,0.198 10 false A86
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A86-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A86 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-2 (GND2) - Body ground Always Below 1 Ω
A86-8 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR