Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P161D  Starter Delay Circuit  


DESCRIPTION

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

By monitoring the condition of the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation), the engine stop and start ECU detects if the transistor of the starter delay circuit is stuck. If the transistor of the starter delay circuit is stuck on, the engine stop and start ECU blinks the stop and start cancel indicator light and stores DTC P161D. If the transistor of the starter delay circuit is stuck on, the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation) will be activated simultaneously.

A375329E01
0.094,0.073 4.865,0.313 4.771,0.24 12 false w/ Entry and Start System: 4.896,0.313 5.51,0.51 0.615,0.198 10 false BIN1 3.729,0.594 4.188,0.792 0.458,0.198 10 false BBC 4.896,1.031 5.51,1.229 0.615,0.198 10 false BIN2 3.51,1.313 4.448,1.51 0.938,0.198 10 false BBC NO. 2 3.083,1.74 3.24,1.938 0.156,0.198 10 false L 3.073,1.969 3.229,2.167 0.156,0.198 10 false B 3.333,2.188 3.49,2.385 0.156,0.198 10 false P 3.563,2.188 3.719,2.385 0.156,0.198 10 false N 2.771,2.469 4.115,2.958 1.344,0.49 10 false Park/Neutral Position Switch Assembly 1.594,1.948 2.208,2.146 0.615,0.198 10 false STAR 0.813,2.333 2.365,2.906 1.552,0.573 10 false Certification ECU (Smart Key ECU Assembly) 4.896,3.656 5.354,3.854 0.458,0.198 10 false STA 4.896,4.313 5.354,4.51 0.458,0.198 10 false STA2 3.615,3.938 4.844,4.135 1.229,0.198 10 false ST NO. 1 0.865,3.677 2.094,3.875 1.229,0.198 10 false ST 5.073,4.792 6.854,5 1.781,0.208 10 false Engine Stop and Start ECU 2.146,5.01 3.375,5.208 1.229,0.198 10 false ST NO. 2 0.698,4.635 1.927,4.833 1.229,0.198 10 false ST NO. 2 0.438,5.688 1.51,5.885 1.073,0.198 10 false FL MAIN 0.552,7.583 1.625,7.781 1.073,0.198 10 false Battery 4.521,6.833 6.917,7.063 2.396,0.229 10 false Starter Inrush Current Reduction Relay 6.563,5.625 6.719,5.823 0.156,0.198 10 false M 4.667,5.625 4.823,5.823 0.156,0.198 10 false B 4.677,6.219 4.833,6.417 0.156,0.198 10 false S 3.979,6 4.135,6.198 0.156,0.198 10 false M 2.698,6.031 2.854,6.229 0.156,0.198 10 false B 2.698,6.344 3.156,6.542 0.458,0.198 10 false SL2 2.719,7.51 3.177,7.708 0.458,0.198 10 false SL1 3.104,8.458 5.552,8.656 2.448,0.198 10 false Starter Assembly

A375330E01
0.104,0.083 5.063,0.323 4.958,0.24 12 false w/o Entry and Start System: 4.917,0.427 5.531,0.625 0.615,0.198 10 false BIN1 4.917,0.948 5.531,1.146 0.615,0.198 10 false BIN2 3.458,0.698 3.917,0.896 0.458,0.198 10 false BBC 3.26,1.229 4.458,1.417 1.198,0.188 10 false BBC NO. 2 0.833,1.958 1.292,2.156 0.458,0.198 10 false AM2 1.5,1.698 1.958,1.896 0.458,0.198 10 false AM2 2.25,1.823 2.708,2.021 0.458,0.198 10 false ST2 1.448,2.208 2.583,2.854 1.135,0.646 10 false Ignition or Starter Switch Assembly 3.333,1.688 3.49,1.885 0.156,0.198 10 false L 3.323,1.927 3.479,2.125 0.156,0.198 10 false B 3.573,2.146 3.729,2.344 0.156,0.198 10 false P 3.802,2.146 3.958,2.344 0.156,0.198 10 false N 2.969,2.417 4.313,2.875 1.344,0.458 10 false Park/Neutral Position Switch Assembly 4.896,3.635 5.354,3.833 0.458,0.198 10 false STA 4.917,4.292 5.375,4.49 0.458,0.198 10 false STA2 3.635,3.885 4.865,4.083 1.229,0.198 10 false ST NO. 1 0.906,3.667 2.135,3.865 1.229,0.198 10 false ST 2.146,4.948 3.375,5.146 1.229,0.198 10 false ST NO. 2 0.698,4.573 1.927,4.771 1.229,0.198 10 false ST NO. 2 0.448,5.656 1.521,5.854 1.073,0.198 10 false FL MAIN 0.583,7.542 1.656,7.74 1.073,0.198 10 false Battery 5.031,4.74 6.781,4.99 1.75,0.25 10 false Engine Stop and Start ECU 4.5,6.792 6.917,6.99 2.417,0.198 10 false Starter Inrush Current Reduction Relay 6.563,5.604 6.719,5.802 0.156,0.198 10 false M 4.656,5.615 4.813,5.813 0.156,0.198 10 false B 4.656,6.208 4.813,6.406 0.156,0.198 10 false S 4.01,5.99 4.167,6.188 0.156,0.198 10 false M 2.698,5.969 2.854,6.167 0.156,0.198 10 false B 2.688,6.302 3.146,6.5 0.458,0.198 10 false SL2 2.688,7.49 3.146,7.688 0.458,0.198 10 false SL1 3.25,8.427 5.698,8.625 2.448,0.198 10 false Starter Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P161D Starter Delay Circuit Both of the following conditions are met (1 trip detection logic):
·

Ignition switch ON

·

Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds and 3 times or more


Engine stop and start ECU Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



j.

Depress the brake pedal and stop the vehicle.


k.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


l.

Release the brake pedal with the shift lever in D to start the engine.


m.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



n.

Depress the brake pedal and stop the vehicle.


o.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


p.

Release the brake pedal with the shift lever in D to start the engine.


q.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
A346331C71
3.188,0.615 3.708,0.844 0.521,0.229 3.427,1.344 3.469,2.198 true 3.271,1.333 2.708,2.188 true 3.74,1.229 4.563,2.281 true 3.313,0.646 3.771,0.844 0.458,0.198 10 false A66 3.354,2.25 3.719,2.458 0.365,0.208 10 false STA 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.542,2.24 3.156,2.438 0.615,0.198 10 false STA2 4.427,2.313 5.042,2.51 0.615,0.198 10 false DGND
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Connect an oscilloscope to terminals A66-21 (STA), A66-23 (STA2) and A66-6 (DGND).


b.
A285702E14
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.198,1.771 2.958,1.958 1.76,0.188 10 false 0.016 seconds or more 0.031,0.875 1.865,1.073 1.833,0.198 10 false (ST NO. 1 Relay) 0.031,1.458 1.865,1.656 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the ignition switch START.

Item Condition
Tester Connection A66-21 (STA) - A66-6 (DGND)
A66-23 (STA2) - A66-6 (DGND)
Condition Engine started by ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) operation

Result:
Result Proceed to
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes 0.016 seconds or more A
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds B




A

B