Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P2531  Ignition Switch Run Position Circuit Low  


DESCRIPTION

If the engine stop and start ECU receives the off signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU will output DTC P2531.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P2531 Ignition Switch Run Position Circuit Low Both of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.


·

Wire harness or connector

·

IG2 relay

·

EFI-MAIN NO. 1 relay

·

Ignition or starter switch assembly (w/o Entry and Start System)

·

Certification ECU (Smart key ECU assembly) (w/ Entry and Start System)

·

Engine stop and start ECU


Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

for CVT:

Depress the brake pedal and stop the vehicle.

for Manual Transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more. (for CVT: Keep the shift lever in D.)


h.

for CVT:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transaxle:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

for CVT:

Depress the brake pedal and stop the vehicle.

for Manual Transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for CVT: Keep the shift lever in D.)


f.

for CVT:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transaxle:

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A299563E04
6.042,0.969 6.813,1.167 0.771,0.198 10 false IGSW 6.052,1.708 6.667,1.906 0.615,0.198 10 false MREL 5.792,0.854 6.104,1.052 0.313,0.198 10 false 6 5.781,1.604 6.094,1.802 0.313,0.198 10 false 46 6.031,2.531 6.49,2.729 0.458,0.198 10 false A62 6.021,2.708 6.479,2.906 0.458,0.198 10 false ECM 2.01,2.75 4.313,3.031 2.302,0.281 10 false Ignition or Starter Switch Assembly 2.01,2.542 2.323,2.74 0.313,0.198 10 false G4 3.354,1.99 3.51,2.188 0.156,0.198 10 false 3 1.865,1.99 2.021,2.188 0.156,0.198 10 false 4 3,2.021 3.458,2.219 0.458,0.198 10 false IG2 2.094,2.021 2.552,2.219 0.458,0.198 10 false AM2 0.583,2.719 1.042,2.917 0.458,0.198 10 false AM2 6.063,3.823 6.521,4.021 0.458,0.198 10 false IG2 5.719,3.615 6.031,3.813 0.313,0.198 10 false 18 5.688,3.813 6.146,4.01 0.458,0.198 10 false G87 5.698,4.865 6.156,5.063 0.458,0.198 10 false A66 5.781,4.677 5.938,4.875 0.156,0.198 10 false 1 6.052,4.854 6.365,5.052 0.313,0.198 10 false +B 5.698,5.896 6.156,6.094 0.458,0.198 10 false A66 6.031,5.917 6.49,6.115 0.458,0.198 10 false DGND 5.771,5.698 5.927,5.896 0.156,0.198 10 false 6 2.854,5.604 3.969,5.823 1.115,0.219 10 false EFI-MAIN NO. 1 1.167,5.021 2.281,5.24 1.115,0.219 10 false EFI-MAIN NO. 1 2.563,4.49 3.021,4.688 0.458,0.198 10 false IG2 3.667,3.979 4.125,4.177 0.458,0.198 10 false IGN 1.01,3.969 1.469,4.167 0.458,0.198 10 false IG2 3.073,3.677 3.229,3.875 0.156,0.198 10 false 5 2.24,3.708 2.396,3.906 0.156,0.198 10 false 3 2.229,4.094 2.385,4.292 0.156,0.198 10 false 2 3.052,4.104 3.25,4.313 0.198,0.208 10 false 1 3.74,4.74 3.896,4.938 0.156,0.198 10 false 3 2.938,4.75 3.094,4.948 0.156,0.198 10 false 5 3.74,5.135 3.938,5.344 0.198,0.208 10 false 1 2.917,5.125 3.073,5.323 0.156,0.198 10 false 2 0.719,6.594 1.792,6.792 1.073,0.198 10 false Battery 5.333,6.594 7.063,6.833 1.729,0.24 10 false Engine Stop and Start ECU 0.104,0.083 5.063,0.323 4.958,0.24 12 false w/o Entry and Start System: 0.552,5.625 1.625,5.823 1.073,0.198 10 false FL MAIN 4.271,5.021 5.646,5.219 1.375,0.198 10 false EFI NO. 2

A299564E04
6.063,0.969 6.833,1.167 0.771,0.198 10 false IGSW 6.052,1.708 6.667,1.906 0.615,0.198 10 false MREL 5.781,0.854 6.094,1.052 0.313,0.198 10 false 6 5.771,1.594 6.083,1.792 0.313,0.198 10 false 46 6.031,2.531 6.49,2.729 0.458,0.198 10 false A62 6.021,2.729 6.479,2.927 0.458,0.198 10 false ECM 2.896,2.135 3.302,2.323 0.406,0.188 10 false IG2D 3.333,2 3.49,2.198 0.156,0.198 10 false 9 1.917,2 2.073,2.198 0.156,0.198 10 false 2 2.146,2.115 2.458,2.313 0.313,0.198 10 false +B 0.573,2.729 1.031,2.927 0.458,0.198 10 false AM2 1.708,2.531 2.167,2.729 0.458,0.198 10 false G82 1.708,2.729 4.635,3.042 2.927,0.313 10 false Certification ECU (Smart Key ECU Assembly) 6.052,3.823 6.51,4.021 0.458,0.198 10 false IG2 5.688,3.813 6.146,4.01 0.458,0.198 10 false G87 5.74,3.615 6.052,3.813 0.313,0.198 10 false 18 5.688,4.854 6.146,5.052 0.458,0.198 10 false A66 6.042,4.844 6.354,5.042 0.313,0.198 10 false +B 5.698,5.896 6.156,6.094 0.458,0.198 10 false A66 6.042,5.906 6.5,6.104 0.458,0.198 10 false DGND 5.771,4.667 5.927,4.865 0.156,0.198 10 false 1 5.771,5.698 5.927,5.896 0.156,0.198 10 false 6 2.865,5.552 3.958,5.74 1.094,0.188 10 false EFI-MAIN NO. 1 1.156,5.01 2.25,5.198 1.094,0.188 10 false EFI-MAIN NO. 1 1.031,3.969 1.49,4.167 0.458,0.198 10 false IG2 3.865,3.979 4.323,4.177 0.458,0.198 10 false IGN 2.552,4.49 3.01,4.688 0.458,0.198 10 false IG2 2.25,4.104 2.406,4.302 0.156,0.198 10 false 2 3.063,4.115 3.219,4.313 0.156,0.198 10 false 1 2.26,3.688 2.417,3.885 0.156,0.198 10 false 3 3.063,3.708 3.219,3.906 0.156,0.198 10 false 5 2.917,4.75 3.073,4.948 0.156,0.198 10 false 5 3.74,4.729 3.896,4.927 0.156,0.198 10 false 3 2.917,5.146 3.073,5.344 0.156,0.198 10 false 2 3.74,5.146 3.896,5.344 0.156,0.198 10 false 1 5.354,6.625 7.083,6.844 1.729,0.219 10 false Engine Stop and Start ECU 0.76,6.573 1.833,6.771 1.073,0.198 10 false Battery 0.063,0.063 4.833,0.302 4.771,0.24 12 false w/ Entry and Start System: 0.563,5.677 1.635,5.875 1.073,0.198 10 false FL MAIN 4.281,5.021 5.656,5.219 1.375,0.198 10 false EFI NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

for CVT:

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

for Manual Transaxle:

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.


e.

According to the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 227 19
Result:
Tester Display Result Proceed to
IG Switch ON A
OFF B




A

B

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - IG2 RELAY)
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - IG2 RELAY)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Remove the IG2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-18 (IG2) - IG2 relay terminal 5 Always Below 1 Ω
G87-18 (IG2) - Body ground Always 10 kΩ or higher
IG2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RELAY (IG2 RELAY)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)

NG

REPLACE RELAY (IG2-MAIN RELAY)

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION OR STARTER SWITCH ASSEMBLY OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION OR STARTER SWITCH ASSEMBLY OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

w/o Entry and Start System:

Disconnect the G4 ignition or starter switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Entry and Start System
Tester Connection Condition Specified Condition
IG2 relay terminal 1 - G82-9 (IG2D) Always Below 1 Ω
IG2 relay terminal 1 - Body ground Always 10 kΩ or higher
G82-9 (IG2D) - Body ground Always 10 kΩ or higher

w/o Entry and Start System
Tester Connection Condition Specified Condition
IG2 relay terminal 1 - G4-3 (IG2) Always Below 1 Ω
IG2 relay terminal 1 - Body ground Always 10 kΩ or higher
G4-3 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-1 (+B) - EFI-MAIN NO. 1 relay terminal 3 Always Below 1 Ω
A66-1 (+B) - Body ground Always 10 kΩ or higher
EFI-MAIN NO. 1 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ECM (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ECM (IGSW TERMINAL VOLTAGE)
a.
C267933C19
1.604,0.083 2.01,0.313 0.406,0.229 2.229,1.896 1.854,0.885 true 1.656,0.125 2.115,0.323 0.458,0.198 10 false A62 2.094,1.927 2.802,2.115 0.708,0.188 10 false 6 (IGSW) 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-6 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT RELAY (EFI-MAIN NO. 1 RELAY)

NG

8.INSPECT RELAY (EFI-MAIN NO. 1 RELAY)
a.

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE RELAY (EFI-MAIN NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
HINT:

If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN NO. 1 relay circuit is suspected.


a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI-MAIN NO. 1 relay terminal 1 - A62-46 (MREL) Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 1 - Body ground Always 10 kΩ or higher
A62-46 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (IG2D TERMINAL VOLTAGE)

OK (w/o Entry and Start System)

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (IG2D TERMINAL VOLTAGE)
B264896C67
2.146,0.896 2.51,1.125 0.365,0.229 1.979,1.74 1.792,2.365 true 0.198,0.115 0.385,0.271 0.188,0.156 10 *a 1.635,2.385 2.24,2.563 0.604,0.177 10 IG2D 2.208,0.938 2.573,1.198 0.365,0.26 10 G82
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-9 (IG2D) - Body ground Ignition switch ACC Below 1 V
G82-9 (IG2D) - Body ground Ignition switch ON 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY