Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) U

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A372146E01
1.594,0.208 1.948,0.469 0.354,0.26 3.198,0.208 3.552,0.469 0.354,0.26 5.031,0.188 5.385,0.448 0.354,0.26 3.198,2.063 3.552,2.323 0.354,0.26 1.156,2.01 1.51,2.271 0.354,0.26 5.573,2.073 5.927,2.333 0.354,0.26 1.646,0.25 2.104,0.448 0.458,0.198 10 false A86 3.26,0.25 3.719,0.448 0.458,0.198 10 false A66 5.083,0.24 5.542,0.438 0.458,0.198 10 false G87 5.625,2.115 6.083,2.313 0.458,0.198 10 false G87 3.26,2.104 3.719,2.302 0.458,0.198 10 false A66 1.208,2.052 1.667,2.25 0.458,0.198 10 false A86

a.

Disconnect the A86, A66 and G87 engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A86-1 (BIN2) - Body ground R - Body ground Battery Always 9.5 to 14 V
A86-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
A86-3 (BIN1) - Body ground L - Body ground Battery Always 9.5 to 14 V
A86-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-1 (+B) - Body ground B - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A66-6 (DGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-10 (NE) - Body ground P - Body ground Engine speed signal from ECM Always 10 kΩ or higher
G87-13 (CANH) - Body ground LG - Body ground CAN communication Always 200 Ω or higher
G87-14 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G87-18 (IG2) - Body ground V - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - Body ground for LHD: L - Body ground
for RHD: W - Body ground
Ignition switch signal Ignition switch ACC 9.5 to 14 V
G87-21 (IG1) - Body ground L - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the A86, A66 and G87 engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for CVT

*2: for Manual Transaxle

A86-6 (OP21) - A66-6 (DGND)*1 R - W-B Oil pump assembly with motor (continuously variable transaxle assembly) drive power source signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


10.5 to 16 V
A66-3 (BRE2) - Body ground G - Body ground Ground (vacuum sensor assembly (brake booster pressure sensor)) Always Below 1 Ω
A66-4 (NPS) - A66-6 (DGND)*2 LG - W-B Neutral position switch signal
·

Ignition switch ON

·

Shift lever in neutral


8.1 to 12 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0 to 5.2 V
A66-7 (BNT1) - A66-6 (DGND) R - W-B Engine hood courtesy switch (Hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A66-9 (OPM1) - A66-6 (DGND)*1 LG - W-B Oil pump assembly with motor (continuously variable transaxle assembly) directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


Pulse generation
(see waveform 1)
A66-10 (NE) - A66-6 (DGND) P - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 2)
A66-11 (CLU) - A66-6 (DGND)*2 L - W-B Clutch start switch assembly (for upper) signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A66-13 (PB) - A66-3 (BRE2) SB - G Vacuum sensor assembly (brake booster pressure sensor) signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly (brake booster pressure sensor)


3.4 to 3.8 V
A66-14 (BRVC) - A66-6 (DGND) P - W-B Vacuum sensor assembly (brake booster pressure sensor) power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A66-17 (CLL) - A66-6 (DGND) W - W-B Park/neutral position switch assembly signal*1
·

Ignition switch ON

·

Shift lever not in P or N


8 to 14 V
·

Ignition switch ON

·

Shift lever in P or N


Below 3.0 V
Clutch start switch assembly (for lower) signal*2
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A66-21 (STA) - A66-6 (DGND) LG - W-B Starter pinion operation signal Cranking 6.0 V or more
A66-23 (STA2) - A66-6 (DGND)*1 V - W-B Starter motor operation signal Cranking 6.0 V or more
A66-27 (NOPM) - A66-6 (DGND)*1 G - W-B Oil pump assembly with motor (continuously variable transaxle assembly) speed signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


Pulse generation
(see waveform 3)
G87-1 (IG31) - A66-6 (DGND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-2 (B41) - A66-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
G87-3 (IG41) - A66-6 (DGND) L- W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-5 (ECAN) - A66-6 (DGND) R - W-B Stop and start system cancel switch (Combination switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (Combination switch assembly) pressed


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (Combination switch assembly) not pressed


8 to 14 V
G87-6 (IG11) - A66-6 (DGND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-10 (IG12) - A66-6 (DGND) P - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-12 (B42) - A66-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
G87-18 (IG2) - A66-6 (DGND) V - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - A66-6 (DGND) for LHD: L - W-B
for RHD: W - W-B
Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
G87-21 (IG1) - A66-6 (DGND) L - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-24 (AC41) - A66-6 (DGND) G - W-B Backup boost converter signal Ignition switch ACC 10.5 to 16 V


e.
A329962E01
0.073,0.052 1.302,0.25 1.229,0.198 10 false 5 V/DIV. 1.135,2 1.958,2.177 0.823,0.177 10 false 5 ms./DIV. 2.885,1.25 3.344,1.448 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection A66-9 (OPM1) - A66-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed




f.
A318633E03
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Waveform 2

Item Content
Tester Connection A66-10 (NE) - A66-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


g.
A112562E03
2.844,1.219 3.156,1.375 0.313,0.156 10 false GND 0.094,0.042 1.177,0.344 1.083,0.302 10 false 5 V/DIV. 1.25,1.99 2.323,2.177 1.073,0.188 10 false 5 ms./DIV.

Waveform 3

Item Content
Tester Connection A66-27 (NOPM) - A66-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed