Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below.


Signals (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Release and depress brake pedal with ignition switch ON

WIRING DIAGRAM

A371194E03
5.521,1.771 5.677,1.969 0.156,0.198 10 false 3 5.521,1.385 5.677,1.583 0.156,0.198 10 false 5 6,1.375 6.271,1.594 0.271,0.219 10 false 34 4.688,0.594 4.844,0.792 0.156,0.198 10 false 7 4.698,1.396 4.854,1.594 0.156,0.198 10 false 6 4.875,0.49 5.031,0.688 0.156,0.198 10 false B 5.333,0.49 5.49,0.688 0.156,0.198 10 false L 5.333,1.25 5.49,1.448 0.156,0.198 10 false L 4.875,1.26 5.031,1.458 0.156,0.198 10 false B 6.229,0.333 6.74,0.552 0.51,0.219 10 false STP 6.229,1.156 6.656,1.344 0.427,0.188 10 false ST1- 5.99,0.583 6.281,0.792 0.292,0.208 10 false 35 5.51,0.594 5.667,0.792 0.156,0.198 10 false 3 5.135,1.646 5.563,1.833 0.427,0.188 10 false GND 4.781,2.167 5.208,2.354 0.427,0.188 10 false A77 6.25,2.583 6.677,2.771 0.427,0.188 10 false A61 4.76,2.365 5.906,2.75 1.146,0.385 10 false Stop Light Switch Assembly 6.229,2.76 6.74,2.948 0.51,0.188 10 false ECM 4.104,0.625 4.615,0.844 0.51,0.219 10 false STP 0.635,0.646 1.146,0.865 0.51,0.219 10 false ALT 0.646,1.438 1.156,1.656 0.51,0.219 10 false IG2 0.646,2.052 1.156,2.271 0.51,0.219 10 false AM2 0.427,2.75 1.063,2.969 0.635,0.219 10 false FL MAIN 1.823,3.375 2.333,3.594 0.51,0.219 10 false IG2D 0.625,3.865 1.135,4.083 0.51,0.219 10 false Battery 1.302,2.302 1.813,2.521 0.51,0.219 10 false G4 1.313,2.458 2.49,2.802 1.177,0.344 10 false Ignition Switch Assembly*1 1.365,2.021 1.875,2.24 0.51,0.219 10 false AM2 1.948,2.01 2.458,2.229 0.51,0.219 10 false IG2 3.229,2.219 3.74,2.438 0.51,0.219 10 false IG2 4.115,1.417 4.625,1.635 0.51,0.219 10 false IGN 2.271,2.01 2.427,2.208 0.156,0.198 10 false 3 1.167,2.01 1.323,2.208 0.156,0.198 10 false 4 2.875,2.01 3.031,2.208 0.156,0.198 10 false 1 2.885,1.375 3.042,1.573 0.156,0.198 10 false 3 3.688,2.01 3.844,2.208 0.156,0.198 10 false 2 3.677,1.385 3.833,1.583 0.156,0.198 10 false 5 2.229,3.5 2.74,3.719 0.51,0.219 10 false 9 1.396,3.792 1.906,4.01 0.51,0.219 10 false G82 1.385,3.979 3.583,4.385 2.198,0.406 10 false Certification ECU (Smart key ECU Assembly)*2 4.771,3.5 6.667,3.719 1.896,0.219 10 false *1: w/o Entry and Start System 4.781,3.865 6.677,4.083 1.896,0.219 10 false *2: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
E270270C16
0.135,1.042 0.604,1.458 0.469,0.417 2.365,1.198 2.667,1.875 true 0.25,1.177 0.708,1.375 0.458,0.198 10 false A77 2.667,1.938 2.823,2.135 0.156,0.198 10 false B 0.115,0.188 0.427,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
E270270C17
0.135,1.042 0.625,1.458 0.49,0.417 2.438,1.833 2.104,1.229 true 0.25,1.177 0.708,1.375 0.458,0.198 10 false A77 2.49,1.854 2.646,2.052 0.156,0.198 10 false B 0.115,0.188 0.427,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-6 (B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (IG2 RELAY - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.
A275087C02
0.281,2.615 0.667,2.875 0.385,0.26 2.167,4.198 1.677,3.677 true 2.604,2.771 1.76,3.667 true 0.49,0.365 0.802,0.521 0.313,0.156 10 *a 2.365,0.396 2.677,0.552 0.313,0.156 10 *b 1.594,2.49 1.906,2.646 0.313,0.156 10 *c 0.354,2.667 0.813,2.865 0.458,0.198 10 A61 2.667,2.656 3.323,2.844 0.656,0.188 10 35 (STP) 2.021,4.219 2.719,4.417 0.698,0.198 10 34 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Switch Condition
A61-34 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A61-35 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-5 (L) - A61-34 (ST1-) Always Below 1 Ω
A77-3 (L) - A61-35 (STP) Always Below 1 Ω
A77-5 (L) or A61-34 (ST1-) - Body ground Always 10 kΩ or higher
A77-3 (L) or A61-35 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LAMP SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IG2 RELAY - STOP LIGHT SWITCH ASSEMBLY)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 5 - A77-6 (B) Always Below 1 Ω
IG2 relay terminal 5 or A77-6 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR