Home › Engine / Hybrid System › 2WW STARTING › STARTER › from 2015.10
RM3090E _51 Engine / Hybrid System _044379 2WW STARTING _0219541 STARTER A

2WW STARTING  STARTER  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A329170

Remove the nut and disconnect the field coil lead wire from terminal C.


b.
A329171

Using a T20 "TORX" socket wrench, remove the 3 screws that hold the magnet switch to the starter drive housing assembly.


c.

Remove the magnet switch from the starter drive housing assembly.


d.
A329172C01
0.958,0.563 1.406,0.563 false 1.844,0.5 2.021,0.281 2.021,0.281 2.188,0.281 false 2.458,0.969 2.635,0.75 2.635,0.75 2.802,0.75 false 0.813,0.458 1.125,0.615 0.313,0.156 10 false *1 2.24,0.167 2.552,0.323 0.313,0.156 10 false *a 2.865,0.646 3.177,0.802 0.313,0.156 10 false *b
*1 Pinion Drive Lever
*a Plunger
*b Return Spring


Remove the return spring.


e.

Remove the plunger from the pinion drive lever.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
A329173

Remove the 2 through bolts and starter yoke assembly together with the starter armature assembly from the starter drive housing assembly.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A104840

Secure the starter yoke assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Remove the 2 screws and starter commutator end frame cover from the starter commutator end frame.


c.
A104841C03
1.156,0.823 2.177,0.781 false 2.219,0.656 2.573,0.875 0.354,0.219 10 false *a
*a Slotted Washer


Remove the slotted washer.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



d.
A104843C07
1.802,0.781 2.271,0.49 2.271,0.49 2.531,0.49 false 1.448,1.51 1.448,1.865 false 1.385,0.906 0.5,0.906 false 2.583,0.406 2.896,0.563 0.313,0.156 10 false *a 1.396,1.896 1.708,2.052 0.313,0.156 10 false *b 0.313,0.792 0.625,0.948 0.313,0.156 10 false *a
*a Washer
*b Starter Commutator End Frame


Remove the 2 washers from the starter commutator end frame.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



e.

Remove the starter commutator end frame from the starter yoke assembly.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



f.
A104844C05
0.75,1.021 0.896,1.708 0.896,1.708 1.125,1.708 false 0.573,0.344 0.802,0.188 0.802,0.188 0.969,0.188 false 2.719,0.188 2.875,0.188 2.875,0.188 2.979,0.813 false 1.021,0.083 1.333,0.24 0.313,0.156 10 true *a 1.177,1.604 1.49,1.813 0.313,0.208 10 true *1 2.542,0.094 2.74,0.292 0.198,0.198 10 false *b
*1 Starter Brush Holder Assembly
*a Rubber
*b Spring


Remove the starter brush holder assembly from the starter armature assembly.

NOTICE:
·

Do not pull on the rubber.

·

Use caution to prevent the starter armature assembly from dropping.




Hide 28160 4.REMOVE STARTER ARMATURE ASSEMBLY

a.
A105361C01
1.271,0.49 1.792,0.49 false 1.594,1.76 2.083,1.76 false 1.844,0.427 2.156,0.583 0.313,0.156 10 *1 1.417,1.677 1.729,1.833 0.313,0.156 10 *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 28011 5.REMOVE STARTER CLUTCH SUB-ASSEMBLY

a.
A329176

Disengage the 3 claws and remove the frame end cover from the plate.


b.
A329174

Disengage the 3 claws and remove the plate from the planet carrier.


c.
A329179

Remove the 3 planetary gears from the planet carrier shaft sub-assembly.


d.
A329180C01
1.688,0.833 1.948,0.833 1.948,0.833 2.177,1.135 false 0.281,1.49 0.573,1.49 false 1.438,3.792 1.719,3.792 1.719,3.792 1.906,3.313 false 2.781,2.542 2.781,2.24 false 1.51,0.74 1.823,0.896 0.313,0.156 10 false *1 2.76,2.573 3.073,2.729 0.313,0.156 10 false *2 0.115,1.406 0.427,1.563 0.313,0.156 10 false *3 1.281,3.698 1.594,3.854 0.313,0.156 10 false *a
*1 Pinion Drive Lever
*2 Starter Drive Housing Cover
*3 Starter Drive Housing Assembly
*a Starter Center Bearing Clutch


Remove the starter center bearing clutch, pinion drive lever and starter drive housing cover from the starter drive housing assembly.


e.
A282528C01
1.49,0.625 0.698,0.625 false 2.073,1.26 2.646,1.26 false 0.5,0.542 0.813,0.698 0.313,0.156 10 *1 2.698,1.177 3.01,1.333 0.313,0.156 10 *2
*1 Pinion Stop Collar
*2 Starter Clutch Sub-assembly


Using a screwdriver, move the pinion stop collar down to the starter clutch sub-assembly.


f.
A104905C02
1.51,0.646 0.552,0.646 false 1.51,0.438 0.917,0.438 false 0.75,0.365 1.063,0.521 0.313,0.156 10 false *1 0.406,0.573 0.719,0.729 0.313,0.156 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar


Using a screwdriver, remove the snap ring.


g.

Remove the pinion stop collar.


h.
A105365C02
1.396,1.688 1.542,1.938 1.542,1.938 1.75,1.938 false 2.417,0.74 2.615,0.396 2.615,0.396 2.854,0.396 false 2.896,0.292 3.208,0.448 0.313,0.156 10 false *1 1.792,1.865 2.104,2.021 0.313,0.156 10 false *2
*1 Starter Clutch Sub-assembly
*2 Planet Carrier Shaft Sub-assembly


Remove the starter clutch sub-assembly from the planet carrier shaft sub-assembly.


Hide 28014 6.REMOVE PLANET CARRIER SHAFT SUB-ASSEMBLY

a.
A105364

Using 2 screwdrivers, remove the snap ring from the planet carrier shaft sub-assembly.


b.
A355168

Remove the washer from the planet carrier shaft sub-assembly.


c.
A105368C03
1.281,0.458 1.677,0.458 false 1.625,1.198 0.927,1.198 false 1.698,0.375 2.01,0.531 0.313,0.156 10 false *1 0.75,1.115 1.063,1.271 0.313,0.156 10 false *2
*1 Planet Carrier
*2 Planet Carrier Shaft Sub-assembly


Remove the planet carrier shaft sub-assembly from the planet carrier.


d.
A339506C01
0.26,0.708 0.542,0.708 false 2.583,0.813 2.865,0.813 false 2.26,1.333 2.542,1.333 false 2.115,1.813 2.396,1.813 false 1.417,1.24 1.417,0.99 false 2.917,0.708 3.229,0.865 0.313,0.156 10 false *1 2.583,1.24 2.896,1.396 0.313,0.156 10 false *2 0.094,0.615 0.406,0.771 0.313,0.156 10 false *3 2.438,1.719 2.75,1.875 0.313,0.156 10 false *1 1.365,1.271 1.677,1.427 0.313,0.156 10 false *1
*1 Damper Rubber
*2 Planet Carrier
*3 Intermediate Sealing


Remove the intermediate sealing and 3 damper rubbers from the planet carrier.