Home › Engine / Hybrid System › 2WW STARTING › STARTER › from 2015.10
RM3090E _51 Engine / Hybrid System _044379 2WW STARTING _0219541 STARTER G

2WW STARTING  STARTER  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

When replacing the starter assembly, it is necessary to replace the starter relay as well.


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A329170

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A355370C01
1.698,0.5 1.875,0.26 1.875,0.26 2.083,0.26 true 1.604,0.708 2.135,1 2.135,1 2.354,1 true 0.552,0.917 0.844,0.917 false 2.125,0.146 2.438,0.302 0.313,0.156 10 false *a 2.385,0.896 2.698,1.052 0.313,0.156 10 false *b 0.417,0.813 0.729,0.969 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Moves outward


Connect a battery to the magnet switch as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



b.
A355371C01
1.833,0.542 1.969,0.208 1.969,0.208 2.188,0.208 true 1.708,0.688 2.26,0.49 2.26,0.49 2.479,0.49 true 0.406,1.188 0.698,1.188 0.698,1.188 0.979,0.927 false 2.25,0.104 2.563,0.26 0.313,0.156 10 false *a 2.521,0.396 2.833,0.552 0.313,0.156 10 false *b 0.25,1.073 0.563,1.229 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect


Perform a hold-in test.

i.

While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.
A355372C01
0.781,0.833 0.938,0.833 false 1.844,0.542 1.948,0.26 1.948,0.26 2.104,0.26 true 2.146,0.167 2.458,0.323 0.313,0.156 10 false *a 0.615,0.76 0.938,0.938 0.323,0.177 10 false *b 1.646,1.438 1.958,1.594 0.313,0.156 10 false *c
*a Terminal 50
*b Starter Body
V100135

Disconnect
V100136

Returns inward


Perform a return test.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform a no-load performance test.

i.
A329170

Connect the field coil lead wire to terminal C with the nut. Make sure that the field coil lead wire is not grounded.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A355373C01
1.083,0.156 1.292,0.156 1.292,0.156 1.646,0.469 true 1.813,0.542 2,0.354 2,0.354 2.198,0.354 true 0.625,0.875 0.927,0.875 false 2.24,0.25 2.552,0.406 0.313,0.156 10 false *a 0.917,0.042 1.229,0.198 0.313,0.156 10 false *b 0.479,0.771 0.792,0.927 0.313,0.156 10 false *c
*a Terminal 30
*b Terminal 50
*c Starter Body
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11 V Below 70 A


If the result is not as specified, replace the starter assembly.



Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A104908

Push in the plunger and check that it returns quickly to its original position.

If the plunger does not operate as specified, replace the magnet starter switch assembly.



b.
A339498C01
1.854,1.104 2.24,1.448 2.24,1.448 2.51,1.448 false 0.958,1.344 1.333,1.344 false 2.573,1.365 2.885,1.521 0.313,0.156 10 false *a 0.792,1.26 1.104,1.417 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A339499C01
2.417,1.615 2.156,1.615 2.156,1.615 1.823,1.104 false 2.427,1.031 2.938,1.031 false 2.479,1.521 2.792,1.677 0.313,0.156 10 false *a 2.979,0.917 3.292,1.073 0.313,0.156 10 false *b
*a Terminal 50
*b Magnet Switch Body


Check the holding coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 -Magnet switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

HINT:

If there is no continuity between any segments, replace the starter armature assembly.


a.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (400-grit) or on a lathe.


b.
A329183C01
2.042,0.896 2.25,0.333 2.25,0.333 2.5,0.333 false 1.344,1.781 1.594,1.781 1.594,1.781 1.802,1.24 false 2.573,0.219 2.885,0.375 0.313,0.156 10 false *a 1.177,1.677 1.49,1.833 0.313,0.156 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always 2.67 to 3.29 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A329184C01
1.823,1.219 2.177,0.417 2.177,0.417 2.438,0.417 false 0.531,1.01 1.052,1.01 false 2.51,0.313 2.823,0.469 0.313,0.156 10 false *a 0.365,0.906 0.677,1.063 0.313,0.156 10 false *b
*a Segment
*b Starter Armature Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A207682C01
2.208,1.5 2.76,1.5 false 0.417,0.438 0.646,0.438 0.646,0.438 0.854,1.052 false 0.219,0.323 0.531,0.479 0.313,0.156 10 false *a 2.833,1.396 3.146,1.552 0.313,0.156 10 false *a
*a Armature Shaft


Check the commutator for runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the runout.

Standard Runout:

0.05 mm (0.00197 in.)


Maximum Runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the starter armature assembly.



e.
A329186

Using a vernier caliper, measure the commutator diameter.

Standard Diameter:

30.2 mm (1.19 in.)


Minimum Diameter:

28.9 mm (1.14 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A105577

Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard Undercut Depth:

1.43 mm (0.0563 in.)


Minimum Undercut Depth:

0.75 mm (0.0295 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A128440C02
2.635,0.927 2.948,1.083 0.313,0.156 10 *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard Length:

12.3 mm (0.484 in.)


Minimum Length:

9.8 mm (0.386 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



b.
A104910E04
1.26,1.177 0.76,1.177 false 1.438,1.677 0.833,1.677 false 2.573,1.313 2.896,1.313 false 2.26,0.854 2.802,0.854 false 0.615,1.104 0.729,1.302 0.115,0.198 10 A 0.708,1.604 0.917,1.813 0.208,0.208 10 B 2.948,1.25 3.146,1.458 0.198,0.208 10 C 2.833,0.792 2.948,0.99 0.115,0.198 10 D

Check the brush holder resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
A - C
B - D
C - D
Always 10 kΩ or higher
A - D
B - C
Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



Hide 28011 5.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A207679C01
1.354,0.323 1.667,0.479 0.313,0.156 10 *a 1.448,1.563 1.76,1.719 0.313,0.156 10 *b
*a Free
*b Lock


Check the clutch pinion gear.

i.

Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the clutch pinion gear does not operate as specified, replace the starter clutch sub-assembly.