Home › Engine / Hybrid System › 2WW STARTING › STARTER › from 2015.10
RM3090E _51 Engine / Hybrid System _044379 2WW STARTING _0219541 STARTER A

2WW STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28014 1.INSTALL PLANET CARRIER SHAFT SUB-ASSEMBLY

a.
A339506C01
0.26,0.708 0.542,0.708 false 2.583,0.813 2.865,0.813 false 2.26,1.333 2.542,1.333 false 2.115,1.813 2.396,1.813 false 1.417,1.24 1.417,0.99 false 2.917,0.708 3.229,0.865 0.313,0.156 10 false *1 2.583,1.24 2.896,1.396 0.313,0.156 10 false *2 0.094,0.615 0.406,0.771 0.313,0.156 10 false *3 2.438,1.719 2.75,1.875 0.313,0.156 10 false *1 1.365,1.271 1.677,1.427 0.313,0.156 10 false *1
*1 Damper Rubber
*2 Planet Carrier
*3 Intermediate Sealing


Install the 3 damper rubbers and intermediate sealing to the planet carrier.


b.
A105368C03
1.281,0.458 1.677,0.458 false 1.625,1.198 0.927,1.198 false 1.698,0.375 2.01,0.531 0.313,0.156 10 false *1 0.75,1.115 1.063,1.271 0.313,0.156 10 false *2
*1 Planet Carrier
*2 Planet Carrier Shaft Sub-assembly


Install the planet carrier shaft sub-assembly to the planet carrier.


c.
A355168

Install the washer to the planet carrier shaft sub-assembly.


d.
A105363

Using a screwdriver, install a new snap ring to the planet carrier shaft sub-assembly.


Hide 28011 2.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.
A282530C01
0.729,1.146 0.885,1.344 0.156,0.198 10 .
V100135

High-temperature Grease


Apply high-temperature grease to the spline of the starter clutch sub-assembly and planet carrier shaft sub-assembly.


b.

Install the starter clutch sub-assembly to the planet carrier shaft sub-assembly.


c.
A339502C01
2.26,1.573 2.031,1.573 2.031,1.573 1.802,1.125 false 2.083,0.219 1.833,0.219 1.833,0.219 1.74,0.646 false 2.146,0.104 2.458,0.26 0.313,0.156 10 false *1 2.302,1.469 2.615,1.625 0.313,0.156 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar
V100135

High-temperature Grease


Apply high-temperature grease to the pinion stop collar and a new snap ring.


d.

Install the pinion stop collar and snap ring.


e.
A104906C05
2.667,0.583 2.958,1.333 2.958,1.333 3.125,1.333 false 1.677,0.135 1.844,0.135 1.844,0.135 2.125,0.427 false 1.51,0.052 1.823,0.208 0.313,0.156 10 false *1 3.198,1.229 3.427,1.385 0.229,0.156 10 false *2
*1 Planet Carrier Shaft Sub-assembly
*2 Snap Ring


Using a vise, compress the snap ring.


f.
A033587C10
0.542,0.792 0.542,1.479 false 0.594,0.615 0.729,0.323 0.729,0.323 0.854,0.323 false 0.896,0.25 1.208,0.406 0.313,0.156 10 false *1 0.469,1.5 0.781,1.656 0.313,0.156 10 false *2
*1 Snap Ring
*2 Pinion Stop Collar


While holding the starter clutch sub-assembly, lightly tap the planet carrier shaft sub-assembly and install the pinion stop collar onto the snap ring with a plastic hammer.


g.
A198324C02
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever.


h.
A329180C01
1.688,0.833 1.948,0.833 1.948,0.833 2.177,1.135 false 0.281,1.49 0.573,1.49 false 1.438,3.792 1.719,3.792 1.719,3.792 1.906,3.313 false 2.781,2.542 2.781,2.24 false 1.51,0.74 1.823,0.896 0.313,0.156 10 false *1 2.76,2.573 3.073,2.729 0.313,0.156 10 false *2 0.115,1.406 0.427,1.563 0.313,0.156 10 false *3 1.281,3.698 1.594,3.854 0.313,0.156 10 false *a
*1 Pinion Drive Lever
*2 Starter Drive Housing Cover
*3 Starter Drive Housing Assembly
*a Starter Center Bearing Clutch


Install the starter center bearing clutch, pinion drive lever and starter drive housing cover to the starter drive housing assembly.


i.
A329181C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and planetary gear shafts of the planet carrier shaft sub-assembly.


j.

Install the 3 planetary gears to the planet carrier shaft sub-assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A105361C01
1.271,0.49 1.792,0.49 false 1.594,1.76 2.083,1.76 false 1.844,0.427 2.156,0.583 0.313,0.156 10 *1 1.417,1.677 1.729,1.833 0.313,0.156 10 *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Install the starter armature assembly to the starter yoke assembly.


Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A104844C06
0.74,1.021 1.094,1.521 1.094,1.521 1.26,1.521 false 0.573,0.344 0.802,0.188 0.802,0.188 0.969,0.188 false 2.719,0.188 2.875,0.188 2.875,0.188 2.979,0.813 false 0.365,1.354 0.365,0.698 true 1.021,0.083 1.333,0.24 0.313,0.156 10 true *a 1.333,1.417 1.646,1.625 0.313,0.208 10 true *1 2.542,0.094 2.74,0.292 0.198,0.198 10 false *b 0.292,1.375 0.604,1.583 0.313,0.208 10 true *c
*1 Starter Brush Holder Assembly
*a Rubber
*b Spring
*c Cutout


Secure the starter yoke assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

While compressing the springs, install the starter brush holder assembly to the starter armature assembly.

NOTICE:
·

Align the cutout of the starter yoke assembly with the rubber and install the starter brush holder assembly.

·

Use caution to prevent the starter armature assembly from dropping.




c.
A104843C07
1.802,0.781 2.271,0.49 2.271,0.49 2.531,0.49 false 1.448,1.51 1.448,1.865 false 1.385,0.906 0.5,0.906 false 2.583,0.406 2.896,0.563 0.313,0.156 10 false *a 1.396,1.896 1.708,2.052 0.313,0.156 10 false *b 0.313,0.792 0.625,0.948 0.313,0.156 10 false *a
*a Washer
*b Starter Commutator End Frame


Install the starter commutator end frame to the starter yoke assembly.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



d.

Install the 2 washers to the starter commutator end frame.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



e.
A282532C03
1.135,0.688 2.083,0.688 false 2.135,0.583 2.448,0.74 0.313,0.156 10 false *a
*a Slotted Washer
V100135

High-temperature Grease


Apply high-temperature grease to the slotted washer.

NOTICE:

Use caution to prevent the starter armature assembly from dropping.



f.

Install the slotted washer.


g.
A104840

Install the starter commutator end frame cover to the starter commutator end frame with the 2 screws.

Torque:
2.1 N*m (21 kgf*cm, 19 in.*lbf)


h.

Engage the 3 claws and install the plate to the planet carrier.


i.

Engage the 3 claws and install the frame end cover to the plate.


Hide 28120 5.INSTALL STARTER YOKE ASSEMBLY

a.
A315895C01
1.167,0.698 1.458,0.521 1.458,0.521 1.677,0.521 false 1.719,1.188 1.906,0.833 1.906,0.833 2.188,0.833 false 1.729,0.417 2.042,0.573 0.313,0.156 10 false *1 2.25,0.729 2.563,0.885 0.313,0.156 10 false *a
*1 Starter Drive Housing Cover
*a Cutout


Align the cutout of the starter yoke assembly with the starter drive housing cover.


b.
A329173

Install the starter yoke assembly to the starter drive housing assembly with the 2 through bolts.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)


Hide 28150 6.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A339504C01
1.167,0.177 1.354,0.177 1.354,0.177 1.427,0.448 false 0.99,0.542 1.406,0.542 false 1.865,0.51 2.01,0.302 2.01,0.302 2.208,0.302 false 0.813,0.438 1.125,0.594 0.313,0.156 10 false *1 2.281,0.198 2.594,0.354 0.313,0.156 10 false *a 0.979,0.073 1.292,0.229 0.313,0.156 10 false *b
*1 Pinion Drive Lever
*a Plunger
*b Hook
V100135

High-temperature Grease


Apply high-temperature grease to the hook.


b.

Hang the hook of the plunger on the pinion drive lever.


c.

Install the return spring to the magnet switch.


d.
A329171

Using a T20 "TORX" socket wrench, install the magnet switch with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.
A329170

Connect the field coil lead wire to terminal C with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)