Home › Engine / Hybrid System › 2WW STARTING › RELAY › from 2015.10
RM3090E _51 Engine / Hybrid System _044379 2WW STARTING _0219544 RELAY G

2WW STARTING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT GLOW PLUG RELAY ASSEMBLY

a.
A372754

Disconnect the glow plug relay connector.


b.

Detach the clamp and remove the glow plug relay.


c.
A201709N01
1.833,0.417 2,0.417 2,0.417 2.292,1.135 true 3,0.417 2.833,0.417 2.833,0.417 2.583,1.135 true 1.833,1.833 2,1.833 2,1.833 2.292,1.365 true 3,1.833 2.833,1.833 2.833,1.833 2.594,1.365 true 0.417,1.219 0.573,1.417 0.156,0.198 10 4 1.271,1.219 1.427,1.417 0.156,0.198 10 3 1.271,0.813 1.427,1.01 0.156,0.198 10 2 0.417,0.802 0.573,1 0.156,0.198 10 1 1.729,0.333 1.885,0.531 0.156,0.198 10 4 3.031,0.333 3.188,0.531 0.156,0.198 10 3 3.042,1.74 3.198,1.938 0.156,0.198 10 2 1.74,1.74 1.896,1.938 0.156,0.198 10 1

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Battery voltage not applied to terminals 3 and 4 10 kΩ or higher
Battery voltage applied to terminals 3 and 4 Below 1 Ω


If the result is not as specified, replace the glow plug relay assembly.



Hide 28300 2.INSPECT STRTER RELAY (ST)

a.
A291372N01
1.677,0.75 2.01,0.75 true 2.604,0.75 2.938,0.75 true 2.438,1.125 2.938,1.125 true 2.448,1.604 2.948,1.604 true 0.271,0.75 0.427,0.948 0.156,0.198 10 5 0.271,1.281 0.427,1.479 0.156,0.198 10 1 1.188,1.292 1.344,1.49 0.156,0.198 10 2 1.188,0.76 1.344,0.958 0.156,0.198 10 3 2.969,0.656 3.125,0.854 0.156,0.198 10 2 1.594,0.656 1.75,0.854 0.156,0.198 10 1 2.969,1.51 3.125,1.708 0.156,0.198 10 3 2.969,1.042 3.125,1.24 0.156,0.198 10 5

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the ST NO. 1 relay.