Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK › from 2015.10
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0049895 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

a.
B421520C01
2.49,1.188 2.042,1.188 true 2.49,3.188 2.042,3.188 true 1.375,4.458 1.552,4.208 true 2.083,4.448 1.896,4.208 true 1.719,4.417 1.719,4.188 true 0.354,2.24 0.667,2.438 0.313,0.198 10 false *a 1.073,3.625 1.385,3.823 0.313,0.198 10 false *c 0.375,0.125 0.688,0.323 0.313,0.198 10 false *b 1.198,4.448 1.448,4.646 0.25,0.198 10 false D+ 1.573,4.427 2.188,4.625 0.615,0.198 10 false ACT- 2.094,4.427 2.708,4.625 0.615,0.198 10 false ACT+ 2.552,3.094 2.865,3.292 0.313,0.198 10 false *1 2.542,1.104 2.854,1.302 0.313,0.198 10 false *1
*1 Latch
*a Open
*b Close
*c Component without harness connected
(Back Door Lock Assembly)


Check the operation of the door lock motor.

i.

Move the back door lock assembly to the close position.


ii.

Apply battery voltage to the door lock motor assembly and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ACT+)
Battery negative (-) → 2 (ACT-)
Close → Open


If the result is not as specified, replace the back door lock assembly.



b.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ACT-) - 3 (D+) Close 10 kΩ or higher
2 (ACT-) - 3 (D+) Open Below 1 Ω


If the result is not as specified, replace the back door lock assembly.



Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

a.
B421517C01
1.063,2.844 1.552,2.844 true 1.885,2.833 2.375,2.833 true 0.948,0.917 1.177,1.125 0.229,0.208 10 true *b 1.688,0.917 1.917,1.125 0.229,0.208 10 true *c 0.958,2.375 1.188,2.583 0.229,0.208 10 false *a 2.427,2.76 2.74,2.958 0.313,0.198 10 false M- 0.844,2.75 1.156,2.948 0.313,0.198 10 false M+ 1.792,1.958 2.021,2.167 0.229,0.208 10 true *b 0.885,1.969 1.115,2.177 0.229,0.208 10 true *c
*a Component without harness connected
(Back Door Lock Assembly)
*b Close Operation Direction
*c Open Operation Direction


Check the operation.

i.

Apply battery voltage and check the operation of the closer motor.

OK:
Battery Connection Result
Battery positive (+) - 1 (M-)
Battery negative (-) - 2 (M+)
Close Operation
Battery positive (+) - 2 (M+)
Battery negative (-) -1 (M-)
Open Operation


If the result is not as specified, replace the back door lock assembly.



b.
B438688C01
1.781,0.396 2.052,0.625 2.052,0.625 2.281,0.625 true 1.156,2.781 1.521,2.781 true 1.917,2.781 2.281,2.781 true 0.292,0.646 1.208,0.844 0.917,0.198 10 false 37°26' 0.896,0.167 1.813,0.365 0.917,0.198 10 false 37°23' 2.344,0.542 3.26,0.74 0.917,0.198 10 false 13°43' 0.167,1.104 0.479,1.302 0.313,0.198 10 false *b 0.688,0.365 1,0.563 0.313,0.198 10 false *c 1.573,0.042 1.885,0.24 0.313,0.198 10 false *d 1.948,0.135 2.26,0.333 0.313,0.198 10 false *e 0.75,2.01 1.063,2.208 0.313,0.198 10 false *a 0.823,2.688 1.281,2.885 0.458,0.198 10 false CLS 2.333,2.708 2.792,2.906 0.458,0.198 10 false E
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the half latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CLS) - 1 (E) Open position Below 1 Ω
3 (CLS) - 1 (E) Open position → Half-latch position Below 1 Ω → 10 kΩ or higher
3 (CLS) - 1 (E) Half-latch position 10 kΩ or higher
3 (CLS) - 1 (E) Full-latch position 10 kΩ or higher
3 (CLS) - 1 (E) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.



c.
B438688C04
1.781,0.396 2.052,0.625 2.052,0.625 2.281,0.625 true 1.917,2.948 2.281,2.948 true 1.917,2.781 2.333,2.521 true 0.292,0.646 1.208,0.844 0.917,0.198 10 false 37°26' 0.896,0.167 1.813,0.365 0.917,0.198 10 false 37°23' 2.344,0.542 3.26,0.74 0.917,0.198 10 false 13°43' 0.167,1.104 0.479,1.302 0.313,0.198 10 false *b 0.688,0.365 1,0.563 0.313,0.198 10 false *c 1.573,0.042 1.885,0.24 0.313,0.198 10 false *d 1.948,0.135 2.26,0.333 0.313,0.198 10 false *e 0.75,2.01 1.063,2.208 0.313,0.198 10 false *a 2.354,2.875 2.813,3.073 0.458,0.198 10 false CTY 2.406,2.438 2.865,2.635 0.458,0.198 10 false E
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the full latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - 4 (CTY) Open position Below 1 Ω
1 (E) - 4 (CTY) Half-latch position Below 1 Ω
1 (E) - 4 (CTY) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ or higher
1 (E) - 4 (CTY) Full-latch position 10 kΩ or higher
1 (E) - 4 (CTY) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.



d.
B438688C05
1.781,0.396 2.052,0.625 2.052,0.625 2.281,0.625 true 1.292,2.406 1.448,2.406 1.448,2.406 1.698,2.729 true 1.917,2.781 2.281,2.781 true 0.292,0.646 1.208,0.844 0.917,0.198 10 false 37°26' 0.896,0.167 1.813,0.365 0.917,0.198 10 false 37°23' 2.344,0.542 3.26,0.74 0.917,0.198 10 false 13°43' 0.167,1.104 0.479,1.302 0.313,0.198 10 false *b 0.688,0.365 1,0.563 0.313,0.198 10 false *c 1.573,0.042 1.885,0.24 0.313,0.198 10 false *d 1.948,0.135 2.26,0.333 0.313,0.198 10 false *e 0.75,2.01 1.063,2.208 0.313,0.198 10 false *a 0.927,2.323 1.385,2.521 0.458,0.198 10 false FSW 2.333,2.708 2.792,2.906 0.458,0.198 10 false E
*a Component without harness connected
(Back Door Lock Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position


Check the resistance of the pawl switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW) - 1 (E) Open position 10 kΩ or higher
2 (FSW) - 1 (E) Open position → Half-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch position 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch position → Full-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
2 (FSW) - 1 (E) Full-latch position 10 kΩ or higher
2 (FSW) - 1 (E) Overstroke position 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.



e.
B438689C01
1.135,3.26 1.323,3.26 1.323,3.26 1.563,2.99 true 1.917,2.771 2.375,2.771 true 1.531,0.292 1.844,0.49 0.313,0.198 10 false *b 0.823,2.208 1.135,2.406 0.313,0.198 10 false *a 0.802,3.188 1.208,3.396 0.406,0.208 10 false OPN 2.427,2.708 2.833,2.917 0.406,0.208 10 false E
*a Component without harness connected
(Back Door Lock Assembly)
*b Sector Gear in Neutral Position


Check the resistance of the sector switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (OPN) - 1 (E) Sector gear in neutral position
(Sector switch on)
Below 1 Ω
6 (OPN) - 1 (E) Sector gear not in neutral position
(Sector switch off)
10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.