When the ignition switch is turned to ON, the battery voltage is applied to IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the EFI-MAIN NO.1 relay and supplying power to either terminal +B or +B2 of the ECM.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B75-16 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-37 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO.1 relay.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Remove the EFI-MAIN NO.1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-46 (MREL) - 1 (EFI-MAIN NO.1 relay) | Always | Below 1 Ω |
| A62-2 (+B) - 3 (EFI-MAIN NO.1 relay) | Always | Below 1 Ω |
| A62-3 (+B2) - 3 (EFI-MAIN NO.1 relay) | Always | Below 1 Ω |
| A62-46 (MREL) or 1 (EFI-MAIN NO.1 relay) - Body ground | Always | 10 kΩ or higher |
| A62-2 (+B) or 3 (EFI-MAIN NO.1 relay) - Body ground | Always | 10 kΩ or higher |
| A62-3 (+B2) or 3 (EFI-MAIN NO.1 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO.1 Relay |
Remove the EFI-MAIN NO.1 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO.1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO.1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO.1 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the IG2 relay.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-37 (IGSW) - 5 (IG2 relay) | Always | Below 1 Ω |
| A62-37 (IGSW) or 5 (IG2 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | IG2 Relay |
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IG2 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IG2 relay) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the certification ECU (smart key ECU assembly) connector.
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - 1 (IG2 relay) | Always | Below 1 Ω |
| G82-9 (IG2D) or 1 (IG2 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>3ZR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-3 (IG2) - 1 (IG2 relay) | Always | Below 1 Ω |
| G4-3 (IG2) or 1 (IG2 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG