Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM(except K111, K111F) › from 2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0219904 SFI SYSTEM(except K111, K111F) J

3ZR-FE ENGINE CONTROL  SFI SYSTEM(except K111, K111F)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST relay drive signal output from the ignition switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


WIRING DIAGRAM

A298885E04
0.604,6.573 1.677,6.771 1.073,0.198 10 false Battery 2.708,6.635 3.781,6.833 1.073,0.198 10 false Fuel Pump 2.708,6.469 3.781,6.667 1.073,0.198 10 false V1 2.396,6.323 3.469,6.521 1.073,0.198 10 false B 2.406,6.854 3.479,7.052 1.073,0.198 10 false E 2.406,6.115 3.479,6.313 1.073,0.198 10 false 4 2.417,7.083 3.49,7.281 1.073,0.198 10 false 5 0.448,4.885 1.521,5.083 1.073,0.198 10 false EFI-MAIN NO.1 0.76,3.792 1.833,3.99 1.073,0.198 10 false IG2 0.74,2.333 1.813,2.531 1.073,0.198 10 false AM2 2.219,4.24 3.292,4.438 1.073,0.198 10 false IG2 2.833,2.073 3.906,2.271 1.073,0.198 10 false IG2 2.26,2.073 3.333,2.271 1.073,0.198 10 false AM2 2.052,1.063 3.125,1.26 1.073,0.198 10 false G82 2.771,0.698 3.844,0.896 1.073,0.198 10 false IG2D 2.042,1.25 3.573,1.719 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly)*1 3.219,0.552 4.292,0.75 1.073,0.198 10 false 9 1.885,2.552 2.958,2.75 1.073,0.198 10 false G4 1.885,2.719 3.729,2.99 1.844,0.271 10 false Ignition Switch Assembly*2 3.292,3.792 4.365,3.99 1.073,0.198 10 false IGN 4.594,4.323 5.344,4.51 0.75,0.188 10 false C/OPN 1.885,5.427 2.958,5.625 1.073,0.198 10 false EFI-MAIN NO.1 3.615,0.604 4.688,0.802 1.073,0.198 10 false *1 3.625,2.083 4.698,2.281 1.073,0.198 10 false *2 1.51,2.094 2.583,2.292 1.073,0.198 10 false *2 2.083,2.083 2.479,2.281 0.396,0.198 10 false 4 3.177,2.073 3.573,2.271 0.396,0.198 10 false 3 1.958,3.458 2.354,3.656 0.396,0.198 10 false 3 2.708,3.458 3.104,3.656 0.396,0.198 10 false 5 2.708,3.823 3.104,4.021 0.396,0.198 10 false 1 1.958,3.813 2.354,4.01 0.396,0.198 10 false 2 4.427,3.51 4.823,3.708 0.396,0.198 10 false 1 5.135,3.51 5.531,3.708 0.396,0.198 10 false 2 5.135,3.854 5.531,4.052 0.396,0.198 10 false 3 4.417,3.854 4.813,4.052 0.396,0.198 10 false 5 2.698,4.594 3.094,4.792 0.396,0.198 10 false 3 1.927,4.583 2.323,4.781 0.396,0.198 10 false 5 2.698,5.052 3.094,5.25 0.396,0.198 10 false 1 1.938,5.052 2.333,5.25 0.396,0.198 10 false 2 5.729,5.177 6.292,5.385 0.563,0.208 10 false A62 5.74,3.625 6.302,3.833 0.563,0.208 10 false A62 5.729,6.365 6.292,6.573 0.563,0.208 10 false A62 5.74,6.823 6.302,7.031 0.563,0.208 10 false B93 5.74,7.198 6.302,7.406 0.563,0.208 10 false B93 5.74,7.021 6.302,7.229 0.563,0.208 10 false 113 5.75,6.625 6.313,6.833 0.563,0.208 10 false 114 5.781,6.156 6.344,6.365 0.563,0.208 10 false 29 5.781,4.99 6.344,5.198 0.563,0.208 10 false 46 5.781,3.438 6.344,3.646 0.563,0.208 10 false 41 6.104,3.51 6.667,3.719 0.563,0.208 10 false FC 6.104,5.073 6.667,5.281 0.563,0.208 10 false MREL 6.344,7.594 6.906,7.802 0.563,0.208 10 false ECM 0.385,8.365 3.115,8.594 2.729,0.229 10 false *2: w/o Entry and Start System 0.396,7.979 3.125,8.208 2.729,0.229 10 false *1: w/ Entry and Start System 3.76,6.354 5.531,6.594 1.771,0.24 10 false from STA Signal Circuit 3.708,6.917 5.229,7.344 1.521,0.427 10 false from Crankshaft Position Sensor 6.104,6.365 6.667,6.573 0.563,0.208 10 false STA 6.094,6.813 6.656,7.021 0.563,0.208 10 false NE+ 6.094,7.219 6.656,7.427 0.563,0.208 10 false NE- 0.448,5.583 1.521,5.781 1.073,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)

B

10.READ VALUE USING GTS (STARTER SIGNAL)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
a.
A298899C01
0.063,0.063 0.375,0.219 0.313,0.156 10 *1 2.042,1.115 2.354,1.271 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 C/OPN Relay


Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT C/OPN RELAY

NG

9.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
3.INSPECT C/OPN RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE C/OPN RELAY

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (C/OPN relay) - A62-21 (FC) Always Below 1 Ω
2 (C/OPN relay) or A62-21 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - V1-4 (B) Always Below 1 Ω
3 (C/OPN relay) or V1-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Inspect fuel pump.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO.1 RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO.1 RELAY)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (C/OPN relay) - 3 (EFI-MAIN NO.1 relay) Always Below 1 Ω
5 (C/OPN relay) or 3 (EFI-MAIN NO.1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
a.

Remove the C/OPN relay and IG2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - 5 (IG2 relay) Always Below 1 Ω
1 (C/OPN relay) or 5 (IG2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (ENGINE SPEED)

NG

11.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG