Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › from 2015.10
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050078 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



a.
B405918C01
1.552,0.885 1.031,0.75 true 1.969,1.26 2.479,1.354 true 1.5,1.271 1.063,1.406 true 1.927,0.885 2.448,0.76 true 1.146,4.479 1.458,4.635 0.313,0.156 10 false *b 0.385,0.302 0.698,0.458 0.313,0.156 10 false *a 0.875,0.656 1.031,0.854 0.156,0.198 10 false B 2.552,1.281 3.167,1.479 0.615,0.198 10 false DOWN 0.813,1.344 1.125,1.542 0.313,0.198 10 false UP 2.542,0.667 3,0.865 0.458,0.198 10 false GND
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/ Jam Protection Function:

i.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (DOWN)


If the result is not as specified, replace the power window regulator motor assembly LH.



b.
E270262C02
1.01,1.281 1,0.25 1,0.25 1.25,0.25 true 2.167,0.75 2.417,0.75 true 2.917,0.75 3.167,0.75 true 1.292,0.177 1.604,0.333 0.313,0.156 10 false *b 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 2.031,0.677 2.188,0.875 0.156,0.198 10 false U 3.208,0.667 3.365,0.865 0.156,0.198 10 false D
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/o Jam Protection Function:

i.

Apply battery voltage to connector terminals 1 (D) and 2 (U).

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).




c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates clockwise
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.
B405917C01
1.531,0.885 0.948,0.771 true 1,1.396 1.49,1.24 true 1.969,1.25 2.5,1.458 true 1.917,0.885 2.479,0.781 true 2.104,4.469 2.417,4.625 0.313,0.156 10 false *b 0.448,0.302 0.76,0.458 0.313,0.156 10 false *a 2.552,1.385 3.167,1.583 0.615,0.198 10 false DOWN 0.75,1.354 1.063,1.552 0.313,0.198 10 false UP 0.813,0.688 0.969,0.885 0.156,0.198 10 false B 2.521,0.698 2.979,0.896 0.458,0.198 10 false GND
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/ Jam Protection Function:

i.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.



b.
E268557C05
2.292,0.51 2.542,0.677 true 3.229,0.5 3,0.677 true 0.833,0.917 0.833,0.25 0.833,0.25 1,0.25 false 1.063,0.177 1.375,0.333 0.313,0.156 10 false *b 0.052,0.021 0.365,0.177 0.313,0.156 10 false *a 2.167,0.417 2.479,0.573 0.313,0.156 10 false U 3.271,0.406 3.396,0.552 0.125,0.146 10 false D
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/o Jam Protection Function:

i.

Apply battery voltage to connector terminals 1 (D) and 2 (U).

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).



ii.

Check that the motor gear rotates smoothly as follows

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates clockwise
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.