Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) J

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  Starter Inrush Current Reduction Relay Circuit  


DESCRIPTION

The starter inrush current reduction relay prevents the battery voltage from becoming dropping excessively while the starter assembly is operating. If the battery voltage drops below the threshold, stop and start control will be prohibited. In order to prevent this, the engine stop and start ECU operates the starter inrush current reduction relay for approximately 0.1 seconds after the ST NO. 2 relay is activated. By allowing current to flow to the starter inrush current reduction relay, the current that flows to the starter motor is reduced, preventing the battery voltage from dropping excessively.

A357107E01
0.74,0.979 1.615,1.177 0.875,0.198 10 false from Battery 0.24,1.292 1.604,1.51 1.365,0.219 10 false from ST NO. 2 Relay 0.115,0.094 3.052,0.333 2.938,0.24 12 false Starter Assembly 4.25,1.719 6.656,1.948 2.406,0.229 10 false Starter Inrush Current Reduction Relay 0.292,2.635 1.656,2.885 1.365,0.25 10 false from ST NO. 1 Relay 2.458,0.875 2.615,1.073 0.156,0.198 10 false B 2.458,1.198 2.917,1.396 0.458,0.198 10 false SL2 2.458,2.542 2.917,2.74 0.458,0.198 10 false SL1 3.729,0.885 3.885,1.083 0.156,0.198 10 false C 4.333,0.51 4.49,0.708 0.156,0.198 10 false B 4.333,1.094 4.49,1.292 0.156,0.198 10 false S 6.375,0.5 6.531,0.698 0.156,0.198 10 false M

CAUTION / NOTICE / HINT

HINT:
·

Starter inrush current reduction relay stuck on:

When the engine is started by stop and start control, a large amount of current will flow to the starter assembly, the battery voltage will drop excessively and stop and start control will be canceled.

·

Starter inrush current reduction relay stuck off:

Operating current will always flow through the starter inrush current reduction relay and the cranking speed will be low.



PROCEDURE

1.CHECK WAVEFORM (STARTER INRUSH CURRENT REDUCTION RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch.

Powertrain > Stop and Start > Active Test
Tester Display
Starter Motor Drive Magnet Switch
50004 227 13

e.

Connect the positive (+) lead of an oscilloscope to the positive (+) battery terminal and the negative (-) lead to the negative (-) battery terminal.


f.

While performing the Active Test "Starter Motor Drive Magnet Switch" to forcibly operate the starter motor, count the number of times the waveform drops.

NOTICE:
·

The Active Test "Starter Motor Drive Magnet Switch" is stopped automatically after the starter motor operates for 3 seconds.

·

Do not forcibly operate the starter pinion.



A285238E02
2.719,0.448 3,0.167 3,0.167 3.333,0.167 false 0.104,0.208 0.719,0.406 0.615,0.198 10 false Normal: 0.146,1.469 0.76,1.667 0.615,0.198 10 false Abnormal: 0.146,2.417 0.76,2.615 0.615,0.198 10 false Abnormal: 1.135,0.896 2.281,1.188 1.146,0.292 10 false 7.6 to 9.3 V* 0.094,0.552 1.021,0.896 0.927,0.344 10 false Approximately 12 V 3.396,0.073 5.469,0.281 2.073,0.208 10 false Approximately 0.1 seconds 2.573,1.344 4.125,1.542 1.552,0.198 10 false Less than 3 seconds 4.667,1.854 6.656,2.052 1.99,0.198 10 false : Voltage drops only 1 time 4.635,2.708 7.073,2.917 2.438,0.208 10 false : Voltage drops excessively only 1 time 4.375,3.438 6.979,3.635 2.604,0.198 10 false *: Varies with battery condition 0.146,1.813 1.073,2.156 0.927,0.344 10 false Approximately 12 V 0.146,2.719 1.073,3.063 0.927,0.344 10 false Approximately 12 V

Standard:

Waveform drops 2 times



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE STARTER INRUSH CURRENT REDUCTION RELAY