Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Radio and display receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

E291289E04
0.844,0.656 1.583,1.198 0.74,0.542 10 false Telephone Microphone Assembly 0.552,2.51 1.292,3.052 0.74,0.542 10 false Q16 0.542,2.667 1.917,2.844 1.375,0.177 10 false Map Light Assembly 0.229,3.323 1.604,3.5 1.375,0.177 10 false *: Shielded 3.365,1.896 3.5,2.052 0.135,0.156 10 false * 4.604,1.906 4.74,2.063 0.135,0.156 10 false * 1.792,0.448 2.406,0.656 0.615,0.208 10 false MACC 1.792,0.833 2.385,1.052 0.594,0.219 10 false MCO+ 1.813,1.219 2.375,1.438 0.563,0.219 10 false MCO- 1.833,2 2.292,2.198 0.458,0.198 10 false SNS2 2.313,0.427 2.927,0.635 0.615,0.208 10 false 3 2.302,0.844 2.917,1.052 0.615,0.208 10 false 4 2.323,1.24 2.938,1.448 0.615,0.208 10 false 6 2.354,2.01 2.969,2.219 0.615,0.208 10 false 5 5.698,0.531 6.313,0.74 0.615,0.208 10 false MACC 5.708,0.948 6.104,1.146 0.396,0.198 10 false MIN+ 5.698,1.333 6.094,1.531 0.396,0.198 10 false MIN- 5.688,1.729 6.417,1.927 0.729,0.198 10 false SGND 5.698,2.135 6.094,2.333 0.396,0.198 10 false SNS2 5.458,2.01 6.073,2.219 0.615,0.208 10 false 6 5.406,1.594 6.021,1.802 0.615,0.208 10 false 18 5.406,1.198 6.021,1.406 0.615,0.208 10 false 19 5.479,0.844 6.094,1.052 0.615,0.208 10 false 5 5.479,0.417 6.094,0.625 0.615,0.208 10 false 4 5.188,2.479 5.802,2.688 0.615,0.208 10 false G143 5.188,2.646 6.906,2.99 1.719,0.344 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK RADIO & DISPLAY RECEIVER ASSEMBLY
a.
E280108C11
0.198,0.917 0.583,1.125 0.385,0.208 2.021,1.323 1.25,1.813 1.25,1.813 1.01,1.813 true 2.167,1.333 2.25,1.896 2.25,1.896 2.406,1.896 true 2.156,1.083 2.292,0.292 2.292,0.292 2.448,0.292 true 0,0 0.313,0.156 0.313,0.156 10 false *a 0.24,0.948 0.76,1.177 0.521,0.229 10 false G143 0.604,1.719 0.958,1.917 0.354,0.198 10 false MIN- 2.469,1.802 3.135,1.979 0.667,0.177 10 false SGND 2.542,0.198 3.031,0.365 0.49,0.167 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-18 (SGND) - Body ground Always Below 1 Ω
G143-19 (MIN-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-4 (MACC) - Q16-3 (MACC) Always Below 1 Ω
G143-5 (MIN+) - Q16-4 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - Q16-6 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω
G143-4 (MACC) - Body ground Always 10 kΩ or higher
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher
G143-6 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY