Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 2WW) › from 2015.10
RM3090E _52 Drivetrain _008754 CLUTCH _0220760 CLUTCH UNIT(for 2WW) A

CLUTCH  CLUTCH UNIT(for 2WW)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C199344C02
1.031,3.552 1.031,3.844 false 2.688,1.219 2.688,1.708 false 0.854,3.938 1.427,4.135 0.573,0.198 10 false SST 2.531,1.729 2.906,1.927 0.375,0.198 10 false SST 2.635,3.354 2.948,3.51 0.313,0.156 10 false *a
*a Transaxle side


Insert SST into the clutch disc assembly, and then insert them into the flywheel sub-assembly.

SST
09301-00310  

NOTICE:

Do not insert the clutch disc assembly in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C299402C03
1.063,0.896 0.729,0.573 0.729,0.573 1.073,0.833 false 1.948,0 2.146,0.219 0.198,0.219 10 true 1 1.083,1.917 1.219,2.083 0.135,0.167 10 false 2 0.854,0.156 0.99,0.323 0.135,0.167 10 false 3 2.073,1.927 2.271,2.094 0.198,0.167 10 true 4 0.594,0.927 0.729,1.094 0.135,0.167 10 false 5 2.5,0.99 2.719,1.198 0.219,0.208 10 true 6 0.542,0.469 0.708,0.635 0.167,0.167 10 false *a
*a Matchmark


Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Install and tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Be sure to uniformly tighten the bolts 180° at a time according to the order in the illustration.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C299403N01
0.074,3.261 0.389,3.424 0.315,0.163 10 SST 0.428,3.365 0.675,3.365 0.675,3.365 0.848,3.574 false

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

SST
09333-00013  

Maximum misalignment:

1.3 mm (0.0512 in.)


If the misalignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.
C304173

Install the release fork support to the manual transaxle assembly.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 31126 5.INSTALL CLUTCH RELEASE FORK BOOT

a.
C299398

Install the clutch release fork boot to the manual transaxle assembly.


Hide 31237 6.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

a.
C299405

Install the clutch release fork support boot and a new snap ring to the clutch release fork sub assembly.


Hide 31204 7.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C299404C02
0,0 0,0 false
V100135

Release hub grease


Apply release hub grease to the clutch release fork sub-assembly where it contacts the clutch release bearing assembly, push rod and release fork support.

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.

Install the release fork to the clutch release bearing assembly with the release bearing hub clip.


Hide 31230 8.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
C202870C02
0,0 0,0 false
V100135

Clutch spline grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



b.
C344789C01
0,0 0,0 false
V100135

Release hub grease


Apply release hub grease to the inside of the clutch release bearing.

Grease:

Toyota Genuine Release Hub Grease or equivalent



c.
C299395

Install the clutch release bearing together with the release fork to the manual transaxle assembly.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.