Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) J

STOP AND START  STOP AND START SYSTEM(for 2WW)  STA Signal Circuit  


DESCRIPTION

While the engine is being cranked, a starter operation request signal is sent to terminal STA of the ECM.

HINT:

If there is an open in the STA circuit of the ECM, stop and start control will be prohibited after the third time the engine is started by stop and start control.

·

Stop and start control will be prohibited until the ignition switch is turned off.

·

The MIL will not illuminate.

·

If there is an open in the STA circuit of the ECM, the engine can still be started using the ignition or starter switch assembly*1 or push start switch assembly*2 , as the ECM also receives the starter operation request signal from the engine stop and start ECU via CAN communication. (Stop and start control is prohibited as the reliability of the signal sent via CAN communication cannot be assured while the voltage drops during operation of the starter assembly.)

*1: w/o Entry and Start System

*2: w/ Entry and Start System



A347476E04
2.667,0.51 4.604,0.75 1.938,0.24 10 false Starter operation request signal 4.26,1.615 5.823,1.833 1.563,0.219 10 false Starter operation request 4.26,2.094 5.823,2.313 1.563,0.219 10 false Starter operation request 5.958,2.51 7.01,2.865 1.052,0.354 10 false Engine Stop and Start ECU 2.385,2.115 3,2.313 0.615,0.198 10 false Open 0.583,2.51 1.042,2.708 0.458,0.198 10 false ECM 0.781,1.875 1.24,2.073 0.458,0.198 10 false STA 6.146,1.885 6.604,2.083 0.458,0.198 10 false STA 6.156,0.833 6.615,1.031 0.458,0.198 10 false CAN 0.75,0.823 1.208,1.021 0.458,0.198 10 false CAN 1.188,3.25 3.938,3.448 2.75,0.198 10 false from ST Fuse 0.833,4.74 3.896,4.938 3.063,0.198 10 false for Starter Assembly 3.885,4 5.115,4.198 1.229,0.198 10 false ST 0.396,5.333 2.156,5.552 1.76,0.219 10 false : CAN Communication Line

WIRING DIAGRAM


A330989E07
5.458,0.625 5.917,0.823 0.458,0.198 10 false G87 5.51,0.427 5.823,0.625 0.313,0.198 10 false 13 5.469,1.021 5.927,1.219 0.458,0.198 10 false G87 5.51,0.833 5.823,1.031 0.313,0.198 10 false 14 5.865,0.656 6.479,0.854 0.615,0.198 10 false CANH 5.875,1.031 6.49,1.229 0.615,0.198 10 false CANL 1.271,0.646 1.885,0.844 0.615,0.198 10 false CANH 1.292,1.042 1.906,1.24 0.615,0.198 10 false CANL 1.792,0.438 2.104,0.635 0.313,0.198 10 false 26 1.802,0.844 2.115,1.042 0.313,0.198 10 false 25 1.375,1.5 1.833,1.698 0.458,0.198 10 false STA 5.521,1.292 5.833,1.49 0.313,0.198 10 false 21 5.885,1.5 6.344,1.698 0.458,0.198 10 false STA 1.792,1.365 2.104,1.563 0.313,0.198 10 false 36 1.146,2.438 1.781,2.656 0.635,0.219 10 false ECM 0.781,2.281 1.24,2.479 0.458,0.198 10 false A62 2.417,3.052 3.49,3.25 1.073,0.198 10 false ST 4.802,3.615 5.875,3.813 1.073,0.198 10 false ST 4.417,3.208 4.573,3.406 0.156,0.198 10 false 2 4.073,3.99 4.229,4.188 0.156,0.198 10 false 3 4.427,3.99 4.583,4.188 0.156,0.198 10 false 1 4.063,3.208 4.219,3.406 0.156,0.198 10 false 5 0.938,4.771 1.646,4.979 0.708,0.208 10 false Battery 0.771,3.708 1.542,3.906 0.771,0.198 10 false FL MAIN 4.75,5.594 5.979,5.792 1.229,0.198 10 false Starter Assembly 4.74,5.438 5.052,5.635 0.313,0.198 10 false B6 4.063,5.052 4.219,5.25 0.156,0.198 10 false 1 0.771,6.208 3.01,6.406 2.24,0.198 10 false : CAN Communication Line 5.188,2.406 6.948,2.823 1.76,0.417 10 false Engine Stop and Start ECU 5.479,1.49 5.938,1.688 0.458,0.198 10 false A66

PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Read the values displayed on the GTS when the ignition switch is ON and to START.

OK:
Tester Display Condition Normal Condition
Starter Signal Ignition switch ON OFF
Engine start ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
2.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the A62 ECM connector.


b.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the A66 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-36 (STA) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR