Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.



CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES


a.

Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.


b.

Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the ignition switch has been turned from off to on (IG) since the last time the system was activated can be stored and displayed.

HINT:
·

When the vehicle is stopped (vehicle speed below 7 km/h (4.3 mph)), turning the ignition switch from off to ON does not cause the value to increase.

·

The value "31" is displayed when the ignition switch was turned ON more than 31 times.




d.

Check freeze frame data when the system operates

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility.


iv.

Select "ABS History".

Chassis > ABS/VSC/TRC > Utility
Tester Display
ABS History
50005 105 8

v.

Check the freeze frame data when the system operates.




CHECK FREEZE FRAME DATA WHEN DTC WAS STORED


a.

Freeze frame data is stored when a DTC is output.


b.

Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.

HINT:

The value "31" is displayed when the ignition switch was turned ON more than 31 times.



d.

Check freeze frame data when DTC is output

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

iv.

Select a DTC to display the freeze frame data.


v.

Check the freeze frame data for the output DTC.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Error or Normal Normal Error: Momentary interruption
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Error or Normal Normal Error: Momentary interruption
EFI Communication Open ECM communication open detection Error or Normal Normal Error: Momentary interruption
Yaw Rate Open Yaw rate sensor open detection Error or Normal Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection Error or Normal Normal Error: Momentary interruption
Steering Open Steering angle sensor open detection Error or Normal Normal Error: Momentary interruption
Master Cylinder Open Master cylinder pressure sensor open detection Error or Normal Normal Error: Momentary interruption
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Error or Normal Normal Error: Momentary interruption
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Error or Normal Normal Error: Momentary interruption
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Normal Error: Momentary interruption
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Normal Error: Momentary interruption
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Error or Normal Normal Error: Momentary interruption
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Error or Normal Normal Error: Momentary interruption
EFI Communication Invalid ECM communication invalid detection Error or Normal Normal Error: Invalid
Number of IG ON Number of operations of ignition switch being turned to ON after storing Freeze Frame Data 0 to 31 - -
Elapsed Time Time elapsed after ignition switch turned ON Min.: 0 sec
Max.: 100661.76 sec
- -
Buzzer Meter buzzer ON or OFF ON: Buzzer ON
OFF: Buzzer OFF
-
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Gear Position Gear position information Fail, 1st-7th, "P, N", 8th, R or Not R Actual gear position -
Shift Lever Position Shift lever position information Fail, 1st-5th, 6th/B, D/M, "P, N" or R Actual shift lever position -
Operated System Operated system status Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys Actual operated system Non: No operation activated
ABS: ABS activated
VSC: VSC activated
TRC: TRC/TRAC activated
BA: BA activated
Fail: Fail safe mode activated
PBA: PBA activated*1
PB: PB activated*1
HA-CTRL: Hill-start assist control activated
TSC: Trailer sway control is activated*2
Sys: System prohibit activated
M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s
Max.: 225 MPa/s
0 MPa/s: When brake pedal is released or pedal held at constant position When brake pedal is being operated: Changes in proportion with pedal movement speed
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
0°/s: Vehicle stopped
-128 to 0°/s: Turning right
0 to 127°/s: Turning left
-
Lateral G Lateral G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During turning: Changes in proportion with acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed FR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed FL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed RR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed RL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.10 m/s2
Max.: 24.90 m/s2
Vehicle stopped: 0 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Real Engine Torque Real engine torque Min.: -1024 Nm
Max.: 1023 Nm
- -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0%
Max.: 127%
Accelerator pedal released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
BS1 Voltage Value +BS voltage value Min.: 0 V
Max.: 20 V
Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0 MPa
Max.: 20 MPa
Different according to target oil pressure of each wheel -
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0 MPa
Max.: 20 MPa
Different according to target oil pressure of each wheel -
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0 MPa
Max.: 20 MPa
Different according to target oil pressure of each wheel -
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0 MPa
Max.: 20 MPa
Different according to target oil pressure of each wheel -
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor Steering angle sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: Positive value increases
Turning right: Negative value decreases
-
TRC/VSC Off Mode TRC/TRAC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC/TRAC off mode
VSC OFF: VSC off mode
-
Master Cylinder Pressure Master cylinder pressure sensor pressure Min.: 0.00 MPa
Max.: 23.28 MPa
Proportional to pedal force: Pedal operated
0.00 MPa: Pedal released
-
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C (-112°F)
Max.: 175°C (347°F)
- -
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned ON Min.: 0 s
Max.: 1275 s
- -
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 25500 rpm
- -
Motor Power Supply Voltage Motor power supply voltage Min.: 0 V
Max.: 20 V
Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
Solenoid Power Supply Voltage Solenoid power supply voltage Min.: 0 V
Max.: 20 V
Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
MT Voltage Value Motor voltage value Min.: 0 V
Max.: 20 V
- Changes in proportion to battery voltage
Stop Light Relay State for ECU Control Stop light control relay (for ECU control) ON or OFF ON: Stop light control relay operating
OFF: Stop light control relay not operating
-
Engine Stop by Stop and Start System Engine stopped by stop and start system status ON or OFF ON: Engine stopped by stop and start control
OFF: Engine not stopped by stop and start control
w/ Stop and Start System
Solenoid State for ECU Control Solenoid (for ECU control) status ON or OFF ON: Solenoid relay operating
OFF: Solenoid relay not operating
-
Motor State for ECU Control Motor (for ECU control) status ON or OFF ON: Motor relay operating
OFF: Motor relay not operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion ON or OFF ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
OFF: No history
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Error or Normal Normal Error: Momentary interruption
Solenoid Power Supply Open Solenoid power supply voltage status Error or Normal Normal Error: Momentary interruption
Motor Power Supply Open Motor power supply voltage status Error or Normal Normal Error: Momentary interruption
Stop Switch Open Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the stop light switch assembly Error or Normal Normal Error: Momentary interruption
IG Switch Ignition switch status ON or OFF - -
Elapsed Time after Freeze Trigger Elapsed time after storing freeze frame data Min.: 0 msec
Max.: 1020 msec
- -

*1: w/ Pre-crash Safety System

*2: w/ Trailer Sway Control





CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTC and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105