The park/neutral position switch assembly and shift lever assembly (transmission control switch) detect the shift lever position and send signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1: 1.
The ignition switch is ON and battery voltage is 10.5 V or higher. 2.
2 or more of the following signals are ON simultaneously: - (NSW, P, N) input signal - R input signal - D input signal 3.
2 seconds 4.
2-trip detection logic DTC Detection Condition 2: 1.
The ignition switch is ON and battery voltage is 10.5 V or higher. 2.
All of the following signals are OFF simultaneously: - NSW input signal - P input signal - R input signal - N input signal - D input signal 3.
60 seconds 4.
2-trip detection logic DTC Detection Condition 3: 1.
The ignition switch is ON and battery voltage is 10.5 V or higher. 2.
Any of the following signals and the M signal are ON simultaneously: - NSW input signal - P input signal - R input signal - N input signal 3.
2 seconds 4.
2-trip detection logic |
·
Harness or connector ·
Park/neutral position switch assembly ·
Shift lever assembly (Transmission control switch) ·
ECM |
Comes on | DTC stored |
This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM. For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or M).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM illuminates the MIL and stores this DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in P or N ·
ON: Shift lever in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in P ·
ON: Shift lever in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in R ·
ON: Shift lever in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in N ·
ON: Shift lever in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (D Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in D or M ·
ON: Shift lever in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Mode Selection SW | Sport mode select switch status | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Tester Display |
|---|
| Sports Mode Selection SW |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Front view of wire harness connector
(to Shift Lever Assembly (Transmission Control Switch)) |
Disconnect the shift lever assembly (transmission control switch) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G36-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| G36-4 (IG) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Lever Assembly (Transmission Control Switch)) |
Disconnect the shift lever assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in M, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G36 shift lever assembly (transmission control switch) connector.
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G36-5 (S) - A62-59 (S) | Always | Below 1 Ω |
| G36-5 (S) - Body ground | Always | 10 kΩ or higher |
| A62-59 (S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B101-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| B101-1 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 9 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P or N | 10 kΩ or higher | |
| 1 (RB) - 3 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 1 (RB) - 8 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 1 (RB) - 7 (DL) | Shift lever in D or M | Below 1 Ω |
| Shift lever not in D or M | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B101 park/neutral position switch assembly connector.
Disconnect the B93 and A62 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B101-3 (PL) - B93-70 (P) | Always | Below 1 Ω |
| B101-2 (RL) - B93-64 (R) | Always | Below 1 Ω |
| B101-8 (NL) - B93-69 (N) | Always | Below 1 Ω |
| B101-7 (DL) - B93-65 (D) | Always | Below 1 Ω |
| B101-4 (B) - A62-23 (NSW) | Always | Below 1 Ω |
| B101-3 (PL) or B93-70 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| B101-2 (RL) or B93-64 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| B101-8 (NL) or B93-69 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| B101-7 (DL) or B93-65 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| B101-4 (B) or A62-23 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG