The ECM controls the secondary oil pressure calibration based on the secondary oil pressure signal output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0841 | Transmission Fluid Pressure Sensor "A" Performance | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1: 1.
The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or higher. 2.
The oil pressure sensor output value is below 0.5 MPa (5.1 kgf/cm2, 73 psi). 3.
2 seconds 4.
1-trip detection logic DTC Detection Condition 2: 1.
The requested oil pressure value is below 1.0 MPa (10.2 kgf/cm2, 145 psi). 2.
The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or higher. 3.
3 seconds 4.
1-trip detection logic |
·
Oil pressure sensor ·
ECM |
Comes on | DTC stored |
| P2829 | Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1: 1.
The requested oil pressure value is below 1.0 MPa (10.2 kgf/cm2, 145 psi). 2.
The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or higher. 3.
3 seconds 4.
1-trip detection logic DTC Detection Condition 2: 1.
The shift lever is in D, and the vehicle speed is less than 8 km/h (5 mph). 2.
The ratio of the transmission revolution sensor (NIN) speed and the transmission revolution sensor (NOUT) speed exceeds a specified value. 3.
0.2 seconds 4.
1-trip detection logic DTC Detection Condition 3: 1.
The oil pressure sensor output value is below 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more. 2.
The actual gear ratio is less than 1.0. 3.
1.5 seconds or more 4.
1-trip detection logic |
·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
The ECM checks for belt clamping high-pressure or low-pressure errors. If a mechanical malfunction is detected in the shift solenoid valve SLS or the oil pressure sensor, the ECM detects the problem, illuminates the MIL and stores a DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Both DTC P0841 and P2829 are output | A |
| Only DTC P0841 is output | B |
| Only DTC P2829 is output | C |
| P0841 and/or P2829 and other DTCs are output | D |
A
B
C
D
The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be conducted after checking and confirming that the engine is operating normally.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.1 to 4.5 MPa (31.6 to 45.9 kgf/cm2, 450 to 653 psi): D position stall speed test ·
2.1 to 4.5 MPa (21.4 to 45.9 kgf/cm2, 305 to 653 psi): R position stall speed test |
- |
| Tester Display |
|---|
| A/T Oil Pressure |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P0841 and/or P2829 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P2829 is output | A |
| DTCs are not output | B |
A
B
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be conducted after checking and confirming that the engine is operating normally.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.1 to 4.5 MPa (31.6 to 45.9 kgf/cm2, 450 to 653 psi): D position stall speed test ·
2.1 to 4.5 MPa (21.4 to 45.9 kgf/cm2, 305 to 653 psi): R position stall speed test |
- |
| Tester Display |
|---|
| A/T Oil Pressure |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P0841 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be conducted after checking and confirming that the engine is operating normally.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.1 to 4.5 MPa (31.6 to 45.9 kgf/cm2, 450 to 653 psi): D position stall speed test ·
2.1 to 4.5 MPa (21.4 to 45.9 kgf/cm2, 305 to 653 psi): R position stall speed test |
- |
| Tester Display |
|---|
| A/T Oil Pressure |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT