Home › Drivetrain › K114 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _044380 K114 MULTIDRIVE / CVT _0220923 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P099B  Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC)  P099C  Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC)  


DESCRIPTION

Based on the signal received by the shift solenoid valve SC, the ECM uses the shift solenoid valve SLU to control the forward and reverse clutch pressure.

If there is an open or short in the shift solenoid valve SC circuit, the ECM stops sending current to the defective shift solenoid valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P099B Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

There is a short in the shift solenoid valve SC circuit.

3.

3 seconds

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SC)

·

ECM


Comes on DTC stored
P099C Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

There is an open in the shift solenoid valve SC circuit.

3.

0.5 seconds

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SC)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SC circuit. If there is an open or short in the shift solenoid valve SC circuit, the ECM detects the problem and stores a DTC.

WIRING DIAGRAM

C264610E48
0.76,2.094 2.292,2.292 1.531,0.198 10 false Shift Solenoid Valve SC 0.927,2.813 3.542,3.177 2.615,0.365 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6.073,2.74 6.521,2.927 0.448,0.188 10 false ECM 0.938,2.646 1.375,2.844 0.438,0.198 10 false B105 5.781,1.021 6.073,1.188 0.292,0.167 10 false SC 5.802,1.854 6.219,2.042 0.417,0.188 10 false E1 5.542,0.906 5.74,1.167 0.198,0.26 10 false 41 5.552,1.75 5.917,1.896 0.365,0.146 10 false 59 4.781,0.906 4.979,1.104 0.198,0.198 10 false 10 6.063,2.573 6.448,2.75 0.385,0.177 10 false B93 4.438,0.906 4.729,1.052 0.292,0.146 10 false SC

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SC)
a.
C298188C08
2.375,1.76 1.729,1.271 true 2.479,1.719 2.938,1.917 0.458,0.198 10 false SC 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (SC) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C02
1.427,0.198 1.813,0.427 0.385,0.229 0.74,1.698 1.052,0.958 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.521,1.729 1.281,1.948 0.76,0.219 10 false 41 (SC) 1.51,0.24 1.969,0.438 0.458,0.198 10 false B93
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-41 (SC) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT