Home › Drivetrain › K114 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _044380 K114 MULTIDRIVE / CVT _0220923 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The ECM uses the shift solenoid valve SLU to perform forward and reverse clutch control or lock-up clutch control.

C300480C04
5.417,2.198 5.563,1.031 true 4.51,1.302 3.969,0.375 3.969,0.375 3.719,0.375 true 4.083,1.563 3.969,2.208 3.969,2.208 3.719,2.208 true 5.594,1.615 5.427,2.208 5.427,2.208 5.177,2.208 true 0.813,1.229 1.063,1.448 0.25,0.219 10 false *a 1.594,2.031 2.24,2.271 0.646,0.24 10 false *b 3.542,0.313 3.854,0.51 0.313,0.198 10 false *1 3.542,2.135 3.854,2.333 0.313,0.198 10 false *2 4.979,2.135 5.292,2.333 0.313,0.198 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

An open or short in the shift solenoid valve SLU circuit is detected.

3.

1 second or more

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SLU)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLU circuit. If there is an open or short in the shift solenoid valve SLU circuit, the ECM detects the problem, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C262369E74
0.813,1.979 2.417,2.146 1.604,0.167 10 false Shift Solenoid Valve SLU 1.094,2.854 3.75,3.25 2.656,0.396 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 1.094,2.656 1.573,2.865 0.479,0.208 10 false B105 5.76,2.729 6.208,2.906 0.448,0.177 10 false B93 5.573,1.677 6,1.865 0.427,0.188 10 false SLU- 5.573,0.896 6.135,1.104 0.563,0.208 10 false SLU+ 5.292,1.552 5.458,1.729 0.167,0.177 10 false 42 5.302,0.771 5.49,0.948 0.188,0.177 10 false 43 4.365,1.552 4.542,1.729 0.177,0.177 10 false 11 4.365,0.771 4.5,0.948 0.135,0.177 10 false 4 5.76,2.906 6.24,3.156 0.479,0.25 10 false ECM 3.927,1.542 4.427,1.771 0.5,0.229 10 false SLU- 3.896,0.771 4.479,1 0.583,0.229 10 false SLU+

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C298188C09
1.094,0.365 1.49,0.917 true 1.125,1.771 1.49,1.281 true 0.719,0.281 1.24,0.479 0.521,0.198 10 false SLU+ 0.76,1.74 1.219,1.938 0.458,0.198 10 false SLU- 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SLU+) - 11 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
4 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
11 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C03
1.427,0.198 1.813,0.427 0.385,0.229 0.813,1.75 1.115,0.958 true 1.573,1.75 1.198,0.958 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.542,1.792 1.302,2.01 0.76,0.219 10 false 42 (SLU-) 1.406,1.813 2.167,2.031 0.76,0.219 10 false 43 (SLU+) 1.51,0.24 1.969,0.438 0.458,0.198 10 false B93
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-43 (SLU+) - B93-42 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
B93-43 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
B93-42 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT