Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE › from 2015.10
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0050288 TRANSMISSION CONTROL CABLE N

EA64 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 33820B 1.ADJUST TRANSAXLE CONTROL CABLE ASSEMBLY

HINT:
·

After the shift lever or the shift cable is replaced, be sure to adjust the transaxle control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the cable must be adjusted.



a.
C341112C01
1.583,1.625 1.667,1.5 1.667,1.5 1.833,1.5 false 0.75,2.333 0.917,2.333 0.917,2.333 1.083,2.135 false 1.583,3.083 2.167,3.135 2.167,3.135 2.333,3.135 true 1.854,1.417 2.167,1.573 0.313,0.156 10 false *1 0.583,2.25 0.896,2.406 0.313,0.156 10 false *2 2.354,3.042 2.667,3.198 0.313,0.156 10 false *3 0.271,1.448 0.583,1.604 0.313,0.156 10 false *a 0.292,2.573 0.604,2.729 0.313,0.156 10 false *b 1.406,2.25 1.615,2.448 0.208,0.198 10 false *c
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
*c Pull


To release the lock (lock condition to lock release condition).


b.
C341113N01
1,1.5 1.333,1.667 0.333,0.167 10 true (*1) 1.917,0.917 2.25,1.083 0.333,0.167 10 true (*2) 2.073,1.667 2.406,1.833 0.333,0.167 10 true (*3)

Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).

i.

Remove the stopper pin, release the lock, and reinsert the stopper pin.



c.
C277909C01
1.896,0.042 2.208,0.24 0.313,0.198 10 false *a
*a Reverse Direction


Turn the shift lever in the reverse direction without pulling up the slider shaft.


d.
C341114C01
1.667,1.635 1.833,1.5 1.833,1.5 2,1.5 false 0.75,2.333 0.917,2.333 0.917,2.333 1.125,2.146 false 1.563,3.083 2.156,3.125 2.156,3.125 2.323,3.125 true 2.021,1.427 2.333,1.583 0.313,0.156 10 false *1 0.583,2.25 0.896,2.406 0.313,0.156 10 false *2 2.344,3.031 2.656,3.188 0.313,0.156 10 false *3 0.292,1.458 0.604,1.615 0.313,0.156 10 false *a 0.302,2.385 0.615,2.542 0.313,0.156 10 false *b 1.427,2.219 1.635,2.427 0.208,0.208 10 false *c
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
*c Push


While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select cable.


e.
C341115C01
2.073,1.469 2.323,1.635 0.25,0.167 10 true *a
*a Pull


Release the shift and select lever shaft straight pin that fixes the shift and select lever assembly.

i.

Pull the pin toward the left front side of the vehicle.



f.
C277910

for new shift lever:

Remove the stopper pin and dispose of it.